Step 4: Connect Drain Hose to Drain Receptacle

Drain Facilities

IMPORTANT: The drain hose installation is a very important factor in the washer installation. If care is not taken when the drain hose is installed, a siphoning action can be started which will cause water to be siphoned from the washer during the cycle.

End of drain hose should never be in water as siphoning action can be started that will cause water to be siphoned back into the washer.

The curved end of drain hose MUST be installed even with or above the height of the cabinet top of the washer to prevent siphoning. Refer to Figure 6.

1

RECOMMENDED

STANDPIPE

HEIGHT

36 inches

MINIMUM (91.44 cm)

2

W294I

1Drain Hose

2Standpipe

Figure 6

The standpipe or drain receptacle must be capable of handling a minimum of 1-1/2 inches (3.8 cm) outside diameter drain hose. The drain hose should fit loose within the standpipe (it should not be snug fit). Never install the drain hose into a “sealed” drain system as air cannot escape and will restrict the water from being drained from the washer. A sealed drain system may also allow water to be pumped back into the washer during agitation. Both of these conditions may result in flooding of the washer.

Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp.

Installation

If necessary, follow the instructions for your type of drain receptacle (high standpipe or low standpipe) to properly install the drain hose.

High Standpipe Installation

NOTE: No. 562P3 Siphon Break Kit and No. 25863 Hose Coupling are not required for this type of installation.

1

2

MAXIMUM

 

STANDPIPE

 

HEIGHT NOT TO

{

EXCEED 5 feet

(1.5 m)

3

W296I

1Drain Hose

2Cut Drain Hose off at This End to Fit the Washer Installation

3Standpipe

Figure 7

IMPORTANT: Drain receptacle must be capable of handling a minimum of 1-1/2 inch (3.8 cm) outside diameter drain hose.

202068

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

9

Page 10 Page 12
Page 11
Image 11
Alliance Laundry Systems TLW12CTLW12C manual Connect Drain Hose to Drain Receptacle, Drain Facilities
Page 10 Page 12

TLW12CTLW12C specifications

Alliance Laundry Systems TLW12CTLW12C is a highly efficient and robust washer-extractor that exemplifies modern engineering in commercial laundry equipment. Designed primarily for high-demand settings such as laundromats, hotels, and large institutions, this model stands out due to its advanced features and exceptional performance.

One of the prominent features of the TLW12CTLW12C is its large capacity, allowing users to process significant loads of laundry in a single cycle. With a drum that can accommodate up to 12 kilograms of laundry, this washer-extractor ensures fewer loads and enhanced productivity, which can greatly benefit businesses aiming to optimize their operations.

The TLW12CTLW12C is equipped with a powerful motor that delivers high extraction speeds, leading to reduced moisture content in the laundry after each cycle. This efficiency translates into shorter drying times, ultimately conserving energy and reducing operational costs. The machine's design also features a robust suspension system that minimizes vibrations, ensuring quiet and stable operation even at full load.

In terms of technology and user control, the TLW12CTLW12C boasts a user-friendly digital control interface, allowing operators to easily select from a wide range of programmable wash cycles tailored for various fabrics and soil levels. This versatility is essential for achieving optimal cleaning results across different textile types, from delicate items to heavily soiled linens.

Another significant characteristic of the TLW12CTLW12C is its energy efficiency. This model is designed with advanced water and energy-saving technologies that not only reduce consumption but also promote environmentally-friendly practices. Additionally, it features automatic water level control and temperature regulation, ensuring consistent wash quality while further minimizing resource usage.

Durability is a pivotal feature of the TLW12CTLW12C, which is constructed from high-quality materials intended to withstand the rigors of commercial usage. The stainless-steel drum and outer construction are resistant to rust and corrosion, ensuring a long lifespan with minimal maintenance.

Overall, the Alliance Laundry Systems TLW12CTLW12C is designed to meet the demanding needs of commercial laundry operations with its blend of capacity, efficiency, flexibility, and durability. Its innovative features make it a worthy investment for those seeking reliable performance in laundry management.
Top Page Image Contents