Operation
Table 2 lists the various displays and what they mean. The operator should become familiar with these computer displays.
Display IndicationsDisplay | Meaning | Display | Meaning | |
FPC3, bP3 | Program identification code (ROM) | Lo | Low water level | |
|
| |||
These are examples only. | nEd | Medium water level | ||
| ||||
Hold | Wait...power has just been turned on. | HI | High water level | |
|
|
|
| |
CY | Cycle (followed by | SUP1 | Supply 1 | |
|
|
|
| |
tESt/CYC* | Test cycle selected. | SUP2 | Supply 2 | |
|
|
|
| |
FAr | Degrees Fahrenheit | SUP3 | Supply 3 | |
|
|
|
| |
CEL | Degrees Celsius | SUP4 | Supply 4 | |
|
|
|
| |
HEAt | Auxiliary heat enabled. | SUP5 | Supply 5 (SETUP option) | |
|
|
|
| |
noHt | Auxiliary heat disabled. | SUP6 | Supply 6 (supply 1 and 5) | |
|
|
|
| |
tFIL | SUP7 | Supply 7 (supply 3 and 4) | ||
|
|
|
| |
ntFL | SLo/For** | Gentle wash speed, forward direction | ||
|
|
|
| |
CooL | Automatic | SLo/rEv** | Gentle wash speed, reverse direction | |
|
|
|
| |
noCL | Automatic | norn/For | Normal wash speed, forward direction | |
Ag 1 | Agitation 1 selected (90% agitation). | norn/rEv | Normal wash speed, reverse direction | |
Ag 2 | Agitation 2 selected (33% agitation). | drAI | Drain enabled. | |
|
|
|
| |
Ag 3 | Agitation 3 selected (10% agitation). | nodr | Drain disabled. | |
|
|
|
| |
Ag 4 | Agitation 4 selected (6.7% agitation). | dISt | Distribution (load balancing before extract) | |
|
|
|
| |
AgSn | Agitation speed normal | SPIn/tInE* | Reads “SPIn” for one second, then “tInE” followed by | |
AgSL** | Agitation speed low | time for spin. | ||
| ||||
|
| |||
|
|
|
| |
PUnP | Pump output enabled (future use only). | SPn1 | Lowest of three spins | |
nPnP | Pump output disabled (future use only). | SPn2 | Middle of three spins | |
PrE | PreWash segment (1st of 11 segments) | SPn3 | Highest of three spins | |
|
|
|
| |
UASH | Wash segment (2nd of 11 segments) | STOP | Stop routine | |
|
|
|
| |
FIL1 | First fill (3rd of 11 segments) | SdLY | Spin coast delay | |
|
|
|
| |
FIL2 | Second fill (4th of 11 segments) | donE | Cycle and stop routine have ended. | |
|
|
|
| |
FIL3 | Third fill (5th of 11 segments) | dFLt | Drive fault detected. | |
|
|
|
| |
FIL4 | Fourth fill (6th of 11 segments) | door | Door not properly closed. | |
|
|
|
| |
FIL5 | Fifth fill (7th of 11 segments) | bAL/FAIL*† | Balancing routine failed during test cycle after | |
|
| |||
FIL6 | Sixth fill (8th of 11 segments) | 7 attempts to balance load. | ||
| ||||
|
| |||
|
|
|
| |
FIL7 | Seventh fill (9th of 11 segments) | FILL/STOP* | Programmed water level not reached after | |
|
| |||
FIL8 | Eighth fill (10th of 11 segments) | 30 minutes. | ||
| ||||
|
| |||
|
|
|
| |
FIL9 | Ninth fill (11th of 11 segments) | FULL | The computer detects low water level or higher when | |
|
| |||
CFIL | Cold fill | none should be present. | ||
| ||||
|
| |||
|
|
|
| |
bFIL | Warm fill (both hot and cold) | rotA | Computer detects possible rotation of motor when there | |
|
| |||
HFIL | Hot fill | should be none. | ||
| ||||
|
| |||
|
|
|
| |
AFIL | Auxiliary fill (SETUP option) | tSFL | Temperature sensor failure or temperature out of range. | |
|
|
|
| |
SPC? | Special test cycle function (if present, ignore) | bAL? | Special test cycle function (if present, ignore) | |
|
|
|
|
* Display indications separated by a slash represent a flashing display.
** For UW100VV and UW125VV models, the
† This occurs only in the TEST cycle and only if the AC inverter drive balance detection is used. If the AC inverter drive balance detection is not used, this will NOT appear during the TEST cycle (note, there are two types of balance systems).
Table 2
14 | © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT | F232123 |