Programming
Table 1 (Continued)
| Cycle Steps Available | Setting Options for Cycle Steps |
(NOTE: WASH, ADD BLEACH, RINSE, and SPIN | (Press START key to advance to next row selection, | |
| LEDs light ONLY when a cycle formula is in | (∧) to increase a value or change, (∨) to decrease a |
| operation.) | value or change, or (∗)to save and exit.) |
|
| |
|
|
|
Rinse 3 (displayed as “rIn3”), lights RINSE LED (during operation) | ||
|
| |
Time for agitation (excludes fill, drain, spin, heat) | 0 or | |
|
| |
Fill valves (temperature) | Cold, Hot, Warm (Cold & Hot) or “EFIL”††† | |
|
| |
Fill water level | Low, Medium, or High | |
|
| |
Supply | None (0), 1, 2 (liquid bleach††††), 3, 4, 5†††††, 6 (1 and 2 | |
|
| together displays as “SUP6”), or 7††††† (Supply 4 and extra |
|
| supply 5 together displays as “SUP7”). |
|
| |
Heat (appears ONLY for models with heat capability) | 00F (no heat for segment), or 80°F to 205°F | |
|
| 00C (no heat for segment), or 27°C to 95°C |
|
| |
Drain (Select Drain or No Drain. Final segment drains in | Drain or No Drain (if No Drain, skips the spin step which | |
stop routine if No Drain is programmed.) | automatically sets that spin time = 0) | |
|
| |
Spin time | 0 or | |
|
| |
|
|
|
Rinse 4 (displayed as “rIn4”), lights RINSE LED (during operation) | ||
|
| |
Time for agitation (excludes fill, heat, drain, spin, heat) | 0 or | |
|
| |
Fill valves (temperature) | Cold, Hot, Warm (Cold & Hot) or “EFIL”††† | |
|
| |
Fill water level | Low, Medium, or High | |
|
| |
Supply | None (0), 1, 2 (liquid bleach††††), 3, 4, 5†††††, 6 (1 and 2 | |
|
| together displays as “SUP6”), or 7††††† (Supply 4 and extra |
|
| supply 5 together displays as “SUP7”). |
|
| |
Heat (appears ONLY for models with heat capability) | 00F (no heat for segment), or 80°F to 205°F | |
|
| 00C (no heat for segment), or 27°C to 95°C |
|
| |
Drain (Select Drain or No Drain. Final segment drains in | Drain or No Drain (if No Drain, skips the spin step which | |
stop routine if No Drain is programmed.) | automatically sets that spin time = 0) | |
|
| |
Spin time | 0 or | |
|
|
|
† | Normal Agitation is 12 seconds forward, 3 seconds | †††† ADD BLEACH LED lights if Supply 2 is the only |
| off, 12 seconds reverse, 3 seconds off, and repeat. | supply programmed and if set up for “bEEP” (refer |
†† | Gentle Agitation is 3 seconds forward, 12 seconds | to Setup Mode section). ADD BLEACH LED and |
| off, 3 seconds reverse, 12 seconds off, and repeat. | Supply 2 signal are on for up to 45 seconds, or until |
††† Extra Fill (“EFIL”) possible only if configured for | the programmed water level is reached, whichever | |
| “EFIL” in Setup Mode. | occurs first. If “bEEP” is enabled, beeper begins |
|
| beeping when Supply 2 comes on and beeps for 8 |
|
| seconds. |
††††† Appears only if “ESUP” (extra supply) configured in Setup Mode.
12 | © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT | F232168 |