Alliance Laundry Systems UW35B2, UW60B2 16

Programming

Heated Models Only

Display shows temperature in degrees F or C. Display will show degrees F if configured for “FAr” in Setup Mode, or degrees C if configured for “CEL” in Setup Mode. Range is 80°F to 205°F, or 00F (no heat for segment), or 27°C to 95°C, or 00C (no heat for segment).

Press the (∧) key to increase, or (∨) key to decrease temperature in one-degree increments. The control will energize heat and pause cycle timing for up to

50 minutes until the programmed temperature is first reached.

NOTE: If temperature not reached after 50 minutes, control resumes cycle.

After cycle resumes, control will attempt to maintain programmed temperature if it senses water in the machine.

NOTE: Temperature display applies ONLY if machine is configured for “HEAt” in Setup Mode. Machine must be equipped with electric or steam heat and a temperature sensor. If configured for “noHt” (no heat capability) in Setup Mode, temperature display does not appear in the segment. After temperature setting, control will skip to “drAI”/“nodr” or Spin Time, depending on version.

If display shows “drAI”/“nodr” during segment programming, a drain step option can be selected. Select “drAI” for a drain step followed by an optional spin. Select “nodr” for no drain step. The machine will proceed directly to the next segment if “nodr”. Change the selection by pressing the (∧) or (∨) key. Press START to continue.

If “drAI” is selected (or if your model does not provide the option of selecting “drAI”/“nodr”), the display will show “SPIn” one second, “tInE” one second, and then the time for spin: “00” (no spin) or 30-240 seconds.

Change the selection by pressing the (∧) or (∨) key. Press START to continue. Then enter the next segment (USH2, USH3, USH4 or after USH4, the “rIN1” segment). Refer to Rinse 1 – Rinse 4 section.

Rinse 1 – Rinse 4

NOTE: Programming a time other than “00” for this step will make the RINSE indicator LED light while this step is running, but not in Program Mode.

The main display shows “rIN1” indicating you are in the Rinse segment (number will represent Rinse cycle selected 1-4). Press START key. Display shows the time for agitation during the step: “00” (skips segment) or 2-15 minutes. This is the time after the fill and before the drain and does not include spin time. Press the (∧) or (∨) key to alter the selection, or the START key to continue.

Display shows “CFIL”, “HFIL”, “bFIL” or “EFIL” for cold, hot, warm (both) or Extra Fill. Press the

(∧) or (∨) key to alter the selection, or the START key to continue.

NOTE: Extra Fill (“EFIL”) possible only if configured for “EFIL” in Setup Mode. If configured, a third valve can be controlled.

Display shows “LO”, “nEd”, or “HI” for low, medium, or high water level, respectively. Press the (∧) or (∨) key to alter the selection, or the START key to continue.

Display shows “SUP0”, “SUP1”, “SUP2”, “SUP3”, “SUP4”, “SUP5” (extra supply), “SUP6”, or “SUP7” (supply 4 and extra supply together), indicating no supply, supply 1, supply 2, supply 3, supply 4, supply 5 (extra supply), supply 6 (supply 1 and 2 together), or supply 7 (supply 4 and extra supply 5 together). Press the (∧) or (∨) key to alter the selection, or the START key to continue.

NOTE: “SUP5” and “SUP7” appear ONLY if control is configured for “ESUP” (spare output set up to operate as an EXTRA supply signal for external chemical) in Setup Mode. If the alternate function for the spare output is selected (“EFIL”), the output will function as an additional fill valve signal with a programmable water level. In this case, extra supply function would NOT be available.

NOTE: If programmed for “SUP2”, the ADD BLEACH indicator LED light turns on and if set up for “bEEP” (refer to Setup Mode section) the buzzer sounds for the first 8 seconds that supply 2 is on.

Press the (∧) or (∨) key to alter the selection or START key to continue.

F232168