Joint Cementing Procedure

All cementing of joints should be done according to the specifications outlined in ASTM D 2855.

NOTE: A sheet metal screw may be used to secure the intake pipe to the connector, if desired. Use a drill or self tapping screw to make a pilot hole.

DANGER

DANGER OF EXPLOSION!

Fumes from PVC glue may ignite during system check. Allow fumes to dissipate for at least 5 minutes before placing unit into operation.

1.	Measure and cut vent pipe to desired length.
2.	Debur and chamfer end of pipe, removing any ridges or
	rough edges. If end is not chamfered, edge of pipe
	may remove cement from fitting socket and result in a
	leaking joint.
3.	Clean and dry surfaces to be joined.
4.	Test fit joint and mark depth of fitting on outside of pipe.
5.	Uniformly apply a liberal coat of PVC primer for PVC or
	use a clean dry cloth for ABS to clean inside socket
	surface of fitting and male end of pipe to depth of fitting
	socket.
6.	Promptly apply solvent cement to end of pipe and inside
	socket surface of fitting. Cement should be applied
	lightly but uniformly to inside of socket. Take care to
	keep excess cement out of socket. Apply second coat

Venting Practices

Piping Suspension Guidelines

SCHEDULE 40

PVC − 5’

all other pipe* − 3’

* See Table 4 for allowable pipe.

NOTE: Isolate piping at the point where it exits the outside wall or roof in order to prevent transmission of vibration to the structure.

Wall Thickness Guidelines

24" maximum 3/4" minimum

ins ide	Wall	outs ide

insulation (if required)

FIGURE 17

to end of pipe.

NOTE: Time is critical at this stage. Do Not allow Primer to dry before applying cement.

7.Immediately after applying last coat of cement to pipe, and while both inside socket surface and end of pipe are wet with cement, forcefully insert end of pipe into socket until it bottoms out. Turn PVC pipe 1/4 turn during assembly (but not after pipe is fully inserted) to distribute cement evenly. Do not turn ABS or cellular core pipe.

NOTE: Assembly should be completed within 20 seconds after last application of cement. Hammer blows should not be used when inserting pipe.

CHIMNEY

OR GAS

VENT

(Check sizing for remaining

appliance)

FURNACE (Removed from from common

vent system)

REPLACING FURNACE THAT WAS PART OF A COMMON VENT SYSTEM

WATER

HEATER

OPENINGS

(To Adjacent

Room)

8.After assembly, wipe excess cement from pipe at end of fitting socket. A properly made join will show a bead around its entire perimeter. Any gaps may indicate an improper defective assembly due to insufficient solvent.

9.Handle joints carefully until completely set.

If this gas furnace replaces a furnace which was commonly vented with another gas appliance, the size of the existing vent pipe for that gas ap- pliance must be checked. Without the heat of the original furnace flue products, the existing vent pipe is probably oversized for the single water heater or other appliance. The vent should be checked for proper draw with the remaining appliance.

FIGURE 18

Page 14 of 48

Issue 1109

506725-01

A95DF, 95G1DF, A93DF, 92G1DF specifications

Allied Air Enterprises offers a range of high-efficiency commercial and residential heating and cooling systems, with models like the 92G1DF, A93DF, 95G1DF, and A95DF gaining popularity for their cutting-edge technology and advanced features. Each of these models stands out in performance, reliability, and energy efficiency, making them excellent choices for diverse applications.

The 92G1DF model features a multi-stage gas valve that enhances temperature regulation, allowing for more precise heating. With an impressive Annual Fuel Utilization Efficiency (AFUE) rating, this furnace efficiently utilizes fuel, resulting in lower energy costs and reduced emissions. Its compact design makes it suitable for installations in tight spaces, while the durable heat exchanger extends the unit’s lifespan.

In contrast, the A93DF is engineered for enhanced comfort and flexibility. This model incorporates a variable-speed blower motor, which adjusts air circulation according to the heating demands in the space. This feature not only maximizes comfort by providing consistent temperatures but also promotes energy savings by reducing unnecessary power consumption. Additionally, the A93DF includes advanced diagnostic capabilities that simplify troubleshooting and maintenance, making it a favorite among HVAC professionals.

The 95G1DF is another noteworthy model that combines versatile performance with exceptional efficiency. This furnace boasts an AFUE rating of up to 95%, making it one of the most efficient models in its class. Its innovative design includes a secondary heat exchanger that captures additional heat from exhaust gases, optimizing energy utilization. Furthermore, the 95G1DF is equipped with an advanced control system that allows homeowners to set specific comfort levels.

Lastly, the A95DF model takes efficiency to a new level. With features such as a modulating gas valve and a variable-speed blower, this unit seamlessly adapts to changing heating needs. The A95DF not only heats a space but also enhances air quality through advanced filtration options. Its whisper-quiet operation adds to user satisfaction, making it ideal for residential settings.

In summary, Allied Air Enterprises' models 92G1DF, A93DF, 95G1DF, and A95DF demonstrate a commitment to innovation and energy efficiency, with features designed to provide superior comfort and reliability. With their advanced technologies and high-performance characteristics, these models are positioned as top contenders in the heating and cooling marketplace, ensuring that customers can enjoy a comfortable environment year-round.

Allied Air Enterprises A93DF, A95DF, 92G1DF, 95G1DF dimensions Joint Cementing Procedure

Models: A95DF 95G1DF A93DF 92G1DF