SYSTEM SPECIFICATIONS

Altec Lansing’s superior sound comes from our patented technology, which utilizes custom-built, high-fidelity drivers, state-of-the-art equalization circuitry, and a harmonious mix of the following specifications:

Total Continuous Power:

4

Watts RMS

Signal to Noise Ratio

 

 

 

 

 

 

@ 1 kHz input:

> 75 dB

 

• Drivers:

2

Watts/channel @ 8 ohms

 

 

 

 

 

 

 

@ 10% THD+N @ 20 Hz – 20 kHz

Drivers:

Four 28 mm full-range

 

 

2

Channels Loaded

 

 

neodymium microdrivers

 

 

 

 

 

 

 

Frequency Response:

60 Hz – 20 kHz

 

 

 

 

 

 

 

 

 

 

 

 

TROUBLESHOOTING

SYMPTOM

POSSIBLE PROBLEM

SOLUTION

No Power LED lit

Universal power supply cord isn’t connected to a wall

Plug the universal power supply into a wall outlet and plug the power supply

(AC Operation).

outlet and/or the power supply connector is not

connector into the power supply jack.

 

plugged into the power supply jack on the back of the

 

 

inMotion iM3 system.

 

 

 

 

 

Surge protector (if used) isn’t powered on.

If the universal power supply cord is plugged into a surge protector, make sure

 

 

the surge protector is switched on.

 

 

 

 

Wall outlet is not functioning.

Plug another device into a wall outlet (same outlet) to confirm the outlet

 

 

is working.

 

 

 

 

Power isn’t turned on.

Position the power switch to the “On” position and press the stand-by button

 

 

(LED will turn green).

 

 

 

No Power LED

No batteries installed.

Install (4) AA batteries into the battery compartments located on the bottom

lit (Battery

 

of the inMotion iM3 system. Make sure the batteries are installed per the

Operation).

 

illustration in the battery compartments.

 

 

 

 

Power isn’t turned on.

Position the power switch to the “On” position and press the stand-by button

 

 

(LED will turn green).

 

 

 

Power LED

Low batteries.

Replace batteries.

turns amber.

 

 

 

 

 

No sound

Power isn’t turned on.

Verify the universal power supply cord is plugged into a wall outlet and the

from speakers.

 

power supply jack.

 

 

 

 

 

Verify batteries are installed if the universal power supply isn’t being used.

 

 

 

 

 

Verify the Power switch has been positioned to the “On” position, the

 

 

stand-by button has been pushed and the LED is illuminated.

 

 

 

 

Volume is set too low.

Press the “+” button to increase the volume.

 

 

 

 

 

Check volume level on alternate audio source device and set at mid-level.

 

 

 

 

iPod is not correctly seated into the docking station.

Remove iPod and re-seat it in the docking station.

 

 

 

 

3.5mm stereo cable isn’t connected to audio source.

Connect 3.5mm stereo cable to the audio source. Make sure the signal cables

 

 

are inserted firmly into the correct jacks.

 

 

 

 

3.5mm stereo cable is connected to wrong output on

Make sure the 3.5mm stereo cable is connected and fully inserted in the

 

audio source.

“line-out,” “audio-out,” or the headphone jack on your sound card or other

 

 

audio source.

 

 

 

 

Problem with audio source.

Test the speakers on another audio source by removing the 3.5mm stereo cable

 

 

from the audio source and connecting it to the “line-out,” “audio-out” or the

 

 

headphone jack of a different audio source (e.g., portable CD, cassette player

 

 

or FM radio).

 

 

 

3

Page 5
Image 5
Altec Lansing iM3 manual System Specifications, Troubleshooting Symptom Possible Problem Solution