Figure 1 - Rigging
DUCT CONNECTIONS
To ensure proper operation, ensure the blower motor is oriented as shown in Figure 5 for horizontal airflow installations.
HORIZONTAL AIRFLOW INSTALLATIONS
(24, 30, 36, 42 AND PHB48 MODELS)
Two
To install the collar connections, remove the two collars, reverse and snap them back into place in the outlet and inlet openings. Be sure the flanges are to the outside of the unit. Secure with screws pro- vided.
HORIZONTAL AIRFLOW INSTALLATIONS
(PHD48/60 and PHB60 models only)
These units are equipped with 14x14 square supply and return air openings for horizontal air flow. The openings are flanged for ease of duct connection. A 16x16 Horizontal Duct Cover kit (CHK001A) can be used with the clips provided with the unit.
THERMOSTAT PLACEMENT
Thermostat should be mounted 5 feet above the floor, on a vibration free inside wall in a room or a hallway that has good air circulation. Movement of air should not be obstructed by furniture, door, draper- ies, etc. The thermostat should not be mounted where it will be af- fected by drafts, hot or cold water pipes or air ducts in walls, radiant heat from fireplace, lamps, the sun, television, etc. Consult the In- struction Sheet packaged with thermostat for mounting instructions.
WARNING
TO AVOID PERSONAL INJURY OR DEATH, DISCONNECT THE ELECTRICAL POWER BEFORE ELECTRICALLY CONNECTING THE UNIT.
THERMOSTAT WIRING
When an electric heater is installed, the thermostat wiring will be made at the heater accessory box.
If a unit is installed without electric heaters, the low voltage wiring to the blower section can be cut, either in the control box area or in the blower section, to allow
See the unit wiring diagram for electrical connections.
ROOM THERMOSTAT |
|
| C/X | G | Y | R | O | W1 | W2 | E |
|
|
|
| ||||||||||||||||
OUTDOOR UNIT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| C/X | G | Y | R | O | W | W1 | W2 |
|
|
|
| |||||||||||||||||
PH__C02E | Wiring shown is for D9945804 (THSMEC1H2BA) thermostat. |
| ||||||||||||||||||||||||||||
|
|
| ||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
ROOM THERMOSTAT |
|
| C/X |
| G |
| Y |
| R |
| O |
|
|
| W2 |
| E |
|
| |||||||||||
OUTDOOR UNIT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
| C/X |
| G |
| Y |
| R |
| O | W |
| W1 |
| W2 |
|
| ||||||||||||||
PH__C02E |
|
|
| Wiring shown is for 10636701(THSADC1H2BA) or |
| |||||||||||||||||||||||||
|
|
|
|
|
|
|
| |||||||||||||||||||||||
|
|
|
|
|
|
| 10636702 (THSMDC1H2BA) thermostat |
|
|
|
|
|
|
| ||||||||||||||||
PHD60 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
| Yellow No. 20 Wire in Blower Section |
|
| |||||||||||||||||
ROOM THERMOSTAT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
| C |
| G |
| Y2 |
| Y1 |
| R | O |
| W1 | W2 | W3 | ||||||||||||||||
OUTDOOR UNIT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
C/X |
| G |
|
|
|
| Y |
| R | O |
| W | W1 | W2 | ||||||||||||||||
PHD60C02E |
|
|
|
|
|
|
|
|
| Wiring shown is for |
|
|
|
|
|
|
|
|
|
| ||||||||||
(HEATER KIT CONTROL BOX) |
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| 1213412 |
|
NOTE: If Electric Heater Kit is not installed or low voltage connection is made in unit control box, connect as follows.
ROOM THERMOSTAT | C | G | Y2 | Y1 | R | O | W1 W2 W3 |
| ||||||
OUTDOOR UNIT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
C | G | Y | Y1 | R | O | W |
|
| ||||||
PHD60C02E |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
(CONTROL BOX) |
|
|
|
| Wiring shown is for 1213412 |
Figure 2 - Typical Thermostat and
Unit 24 Volt Wiring Hoo2kup
ELECTRICAL CONNECTIONS
NOTE: The units are designed for operation on 60 Hz current and at the voltages shown on the rating plate. All internal wiring in the unit is complete. The power supply may be brought into the contactor (refer to unit wiring diagram supplied with unit). Ensure 24 volt wiring is connected between the unit control panel and the room thermostat. Refer to Figure 2 for proper thermostat wiring and Figures 3 and 4 shows the low voltage field connection.
Low Voltage
Terminal Strip
C |
|
G |
|
Y |
|
R |
|
W |
|
W1 | ON |
W2 | ON |
O |
Figure 3 - Low Voltage Connection
Heater Kit Control Box
4