AMD GA-7VASFS-FS

Introduction- 9 -

English

Contents

Main Table of Content Page Installing the motherboard to the chassis Chapter 1 Introduction Features Summary Page Introduction- 7 - GA-7VASFS-FS Motherboard Layout GA-7VASFS-FS FS Block Diagram Page Chapter 2 Hardware Installation Process Step 1: Install the Central Processing Unit (CPU) Step1-1: CPU Speed Setup Step1-2: CPU Installation Step1-3: CPU Heat Sink Installation Step 2: Install memory modules Page Step 3: Install expansion cards Issues To Beware Of When Installing CNR Step 4: Connect ribbon cables, cabinet wires, and power supply Step 4-1: I/O Back Panel Introduction X PS/2 Keyboard and PS/2 Mouse Connector YIEEE 1394 and USB Connector This connector supports IEEE 1394 and USB ZParallel Port, Serial Port and SPDIF Port (LPT/COMA/SPDIF) [USB & LAN Connector Before you connect your device(s) into USB \Audio Connectors Step 4-2: Connectors & Jumper Setting Introduction - 20 -GA-7VASFS-FS Motherboard 1) ATX_12V (+12V Power Connector) 2) ATX (ATX Power) 3) CPU_FAN (CPU FAN Connector) 4) SYS_FAN (System FAN Connector) 5) PWR_FAN (Power Fan Connector) 6) IDE1/ IDE2 (IDE1/IDE2 Connector) 7) FDD (Floppy Connector) 8) S_ATA0/S_ATA1 (Serial ATA Connector) 9) RAM_LED - + 10) PWR_LED - 25 - Hardware Installation Process 11) F_PANEL (2x10 pins connector) 12) BAT (Battery) CAUTION + 13) F_AUDIO (F_AUDIO Connector) 10 9 14) AUX_IN (AUX In Connector) 15) F_ USB1 / F_USB2 (Front USB Connector, Yellow) Be careful with the polarity of the front USB connector. Check the pin assignment while you 210 19 - 28 -GA-7VASFS-FS Motherboard 17) S_IRQ (Serial IRQ Connector) This connector is for special design, for example: PCMCIA add on card. 16) F_1394 (IEEE 1394 Connector) 18) CI (CASE OPEN) 19) CLR_CMOS (Clear CMOS jumper) Page Chapter 3 BIOS Setup ENTERING CONTROL SETUP KEYS The Main Menu Page Standard CMOS Features Date The date format is <week>, <month>, <day>, <year>. Time IDE Primary Master, Slave / IDE Secondary Master, Slave Acoustic Management Drive A / Drive B Floppy 3 Mode Support (for Japan Area) Halt on The category determines whether the computer will stop if an error is detected during power up. Memory The category is display-only which is determined by POST (Power On Self Test) of the BIOS. Advanced BIOS Features Base Memory Extended Memory Password Check System The system will not boot and will not access to Setup page if the correct Full Screen LOGO Show First / Second / Third Boot Device Integrated Peripherals OnChip IDE Channel0 OnChip IDE Channel1 Page Page Power Management Setup ACPI Suspend Type USB Device Wake-up From S3 When set at Enabled, it allows USB Device to activate the system from ACPI S3 power saving mode. Soft-Off by PWRBTN Page PnP/PCI Configurations PNP OS Installed PCI 1/PCI 5 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment PC Health Status Current Voltage (V) Vcore / +3.3V / +5V / +12V /5VSB Current System/CPU Temperature Current CPU/SYSTEM/POWER FAN Speed (RPM) Frequency/Voltage Control DRAM Clock (MHz) Load Fail-Safe Defaults Load Fail-Safe Defaults? (Y/N)?Y Load Fail-Safe Defaults Load Optimized Defaults Load Optimized Defaults? (Y/N)?Y Load Optimized Defaults Set Supervisor/User Password Enter Password: Save & Exit Setup Save to CMOS and EXIT (Y/N)? Y Exit Without Saving Quit Without Saving (Y/N)? N