Manuals / AMD / Computer Equipment / Computer Hardware

AMD SBX-5363 manual 3.8 PNP/PCI Configurations, PNP OS Installed, Reset Configuration Data

Models: SBX-5363

1 55

Download 55 pages 14.5 Kb

Page 41

Image 41

BIOS

3.8 PNP/PCI Configurations

PNP OS Installed

It allows you to enable the PNP OS Install option if it is supported by the OS installed.

Setting: No (Default) /Yes.

Reset Configuration Data

It allows you to determine whether to reset the con?guration data or not. Setting: Disabled (Default) /Enabled.

Resources Controlled By

This PnP BIOS can configure all of the boot and compatible devices with the use of a PnP operating system.

Setting: Auto (ESCD) (Default) /Manual.

IRQ Resources

It allows you to configure the IRQ Resources.

Memory Resources

It allows you to configure the Memory Resources.

- 37 -

Page 41

Image 41

AMD SBX-5363 manual 3.8 PNP/PCI Configurations, PNP OS Installed, Reset Configuration Data, Resources Controlled By

Contents

Page SBX-5363 VersionUsers Manual AMD Geode 3.5 Embedded BoardChapter 1 Introduction Table of ContentsChapter 2 Installation Chapter 4 Appendix Chapter 3 BIOSIntroduction Chapter11 Introduction1.3 Warning 1.1 Copyright Notice1.2 About this Users Manual 1.5 Technical Support 1.4 Replacing the lithium battery1.6 Warranty 1 xSBX-5363 1.7 Packing List1.8 Ordering Information Product Name 1.9 SpecificationIntroduction 1.10 Board DimensionsSD-DIMM1 CFD1 IntroductionInstallation InstallationChapter22 2.1 Jumpers Quick Reference Jumpers CMOS Setup JBAT1JBAT1 JCF1JRS1 Selection 2.1.3 Serial Port SelectJVLCD1 LCD VoltageConnectors 2.2 Connectors Quick ReferenceLabel Function2.2.2 Power Connector 2.2.1 Ethernet ConnectorIDE1 2.2.3 Enhanced IDE ConnectorLCD1 2.2.4 Flat Panel ConnectorLVDS Panel Inverter Connector INV1 Connector LVDS1Description Description2.3.2 USB Ports 2.3 Peripheral Ports 2.3.1 Parallel Port Share with FDD2.3.5 COM1 Port with RS-232C Mode 2.3.4 CRT Display Connector2.3.3 PS/2 Keyboard & Mouse COM2 2.3.6 COM2 Port with RS-232C/422/485 Mode2.3.7 Audio Interface Port 2.4 Switches and Indicators2.3.8 16-bit General Purpose I/O DIO AUDIO1Connector CFD1 2.5 CFD1 Compact Flash II SocketDescription DescriptionBIOS Chapter33 BIOSPress DEL to Enter Setup 3.1 BIOS Introduction3.2 BIOS Setup Date 3.3 Standard CMOS FeaturesMonth 1 to Date 1 to TimeVideo IDE Primary HDDs / IDE Secondary HDDsDrive A Halt On 3.4 Advance BIOS FeaturesQuick Power On Self Test Boot Other Device First/ Second/Third Boot DeviceBoot Up NumLock Status Security OptionCAS Latency 3.5 Advanced Chipset FeaturesInterleave Select XOR BA0XOR Bit Select Flat Panel ConfigurationVideo Memory Size Output displayMaster/Slave Drive PIO Mode 3.6 Integrated Peripherals On-Chip IDE Device On-Chip IDE ChannelIDE Primary Master/Slave UDMA IDE DMA Transfer AccessIDE HDD Block Mode Super IO Device External FDD ControllerUse IR Pins IR Transmission DelayOnboard Serial/Parallel Port UART Mode SelectSerial Port 4 Use IRQ Serial Port 3 Use IRQIT8888 ISA Decode IO Decode I/O Space 0/ 1/ 2/ 3/ 4IT8888 ISA Decode Memory Decode I/O Size 0/ 1/ 2/ 3/ 4Decode Memory Space 0/ 1/ 2 Decode Memory Speed 0/ 1/ 2IT8888 DDMA 3.7 Power Management SetupOnboard Audio ACPI FunctionModem Use IRQ Power ManagementPME Event Function Soft-Off by PWR-BTTNPNP OS Installed 3.8 PNP/PCI ConfigurationsReset Configuration Data Resources Controlled ByBIOS 3.9 PC Health StatusPCI/VGA Palette Snoop 3.11 Set Password 3.10 Load Optimized Defaultsdefault setting is optimal and enabled all high performance features BIOS3.12 Save & Exit Setup 3.13 Exit Without Saving 3.14 BIOS Beep Sound code listBeep Sound Message3.16 Award BIOS Post Codes 3.15 BIOS memory mappingAddress Device DescriptionReserved Reserved Reserved Reserved Reserved Appendix Chapter44Appendix Description 4.1 I/O Port Address MapAddress Device 00000170 Level Function 4.2 Interrupt Request Lines IRQ