American Audio DCD-PRO1000 - page 14

the left channels output.

45. DRIVE 1 DIGITAL OUT - This jack sends a

digital stereo out signal. Use this connection to

create near perfect copies of your disc to a Mini

disc, CD-R, or any other recording device with a

digital input.

46. DRIVE 1 REMOTE JACK - Connect the sup-

plied 8 pin din cable from this jack to the remote

control's channel 1 remote connector. This will

allow you to control the player functions with the

remote unit.

47. POWER CONNECTOR - This is the main

power connection. Only use the supplied polar-

ized power cord. Use of any other power may

result in sever damage to the unit. Be sure the

local power matches the unit’s required power.

48. VOLTAGE SELECTOR - Because power

supplies vary from location to location a voltage

selector switch has been incorporated in the unit's

design. This switch can select a voltage input of

GENERAL FUNCTIONS AND CONTROLS (Cont.)

©American Audio® - www.americanaudio.us - DCD-PRO1000™ Instruction Manual Page 14

120v or 220v to accommodate the two major

power source. Always be sure to disconnect the

power plug before changing the voltage.

49. DRIVE 2 AUDIO OUT R & L - These jacks

send a left and right analog mono output signal.

Use these jacks to send standard audio to a

mixer or receiver. The red colored jack represents

the right channel output and white jack repre-

sents the left channels output.

50. DRIVE 2 DIGITAL OUT - This jack sends a

digital stereo out signal. Use this connection to

create near perfect copies of your disc to a Mini

disc, CD-R, or any other recording device with a

digital input.

51. DRIVE 2 REMOTE JACK - Connect the sup-

plied 8 pin din cable from this jack to the remote

control's channel 2 remote connector. This will

allow you to control the player functions with the

remote unit.

Contents

Main DCD-PRO1000 CONTENTS NOTE: IMPORTANT INFORMATION IMPORTANT SAFETY ITEMS FOR U.S.A. & CANADA MODEL ONLY ELECTRICAL PRECAUTIONS ELECTRICAL SAFETY PRECAUTIONS IMPORTANT SAFETY INSTRUCTIONS American Audio - www.americanaudio.us - DCD-PRO1000 Instruction Manual Page 4 SAFETY INSTRUCTIONS Line Voltage Selection INTRODUCTION UNPACKING SET-UP PRECAUTIONS MAIN FEATURES SET-UP GENERAL FUNCTIONS AND CONTROLS Figure 3 A. CONTROLLER UNIT (FIGURE 3) Page Page B. REMOTE CONTROL - REAR Figure 4 GENERAL FUNCTIONS AND CONTROLS (Cont.) B. TRANSPORT UNIT (FIGURE 4) Page GENERAL FUNCTIONS AND CONTROLS (Cont.) Figure 5 D. LCD DISPLAY PANEL (FIGURE 5) BASIC OPERATIONS 1. LOADING/EJECTING DISCS 2. SELECTING TRACKS 5. STOPPING PLAYBACK - Figures 10 & 11 3. STARTING PLAYBACK - Figure 10 4. AUTO CUE 6. PAUSING - Figure 10 7. FRAME SEARCH 9. SETTING and STORING a CUE POINT: Setting A Cue Point: 8. SCANNING (FAST FORWARD / FAST REVERSE) Storing A Cue Point: 10. CREATING AND PLAYING A SEAMLESS LOOP LCD LOOP INDICA TORS EXITING A LOOP REPLA Y LOOP 11. EDITING A LOOP: 1) 2) 12. Using the Built In Sampler: To create a sample: Page Page Page 17. RECALL FLASH MEMORY: 18. CLEAR ALL MEMORY: 16. SYSTEM MEMORY: 19. FIRMWARE VERSION DISPLAY: Using the Pitch slider (18): 1. PITCH SLIDER (18): Activating the Pitch slider (18): PITCH ADJUSTMENTS: Page 4. JOG WHEEL (20): return to 3. PITCH BEND BUTTONS (25 & 26): FX SELECT: The FX SELECT BUTTON (9) allows you to toggle FILTER/PHASE EFFECT: The Filter and Phase effects tweak SCRATCH/SKID EFFECT: The Scratch Effect simulates real FLANGER/ECHO/ROBOT EFFECT : ROBOT EFFECT : FLANGER EFFECT : ECHO EFFECT : TRANS/PAN EFFECT: The TRANS effect simulates a real-time HOLD BUTTON: PARAMETERS: FLIP-FLOP Note: Compatible Q-Deck Mixer FLIP-FLOP "Q"-START/FLIP-FLOP - FLASH START SET-UP W ARRAN TY INFO RMA TION : 1-YEAR LIMITED WARRANTY SPECIFICATIONS change without any prior written notice.