Manuals / American Dryer Corp / Laundry Appliance / Clothes Dryer

American Dryer Corp ML-122D B. Component Identification, Dryer Front View, Illus. No, Description

Models: ML-122D

1 55

Download 55 pages 50.3 Kb

Page 12

B. COMPONENT IDENTIFICATION

B. COMPONENT IDENTIFICATION

1.Dryer Front View

Illus. No.

Description

1Microprocessor Control/Keyboard (Touch Pad) Panel Assembly (Controls)

2Control (Top Access) Door Assembly

3Main Door Assembly

4Lint Panel Assembly

5Lint Drawer

6Wire Diagram (Located Behind Control Door)

7Top Console (Module) Assembly

8

Image 12

American Dryer Corp ML-122D installation manual B. Component Identification, Dryer Front View, Illus. No, Description

Contents

Installation Manual ML-122DGas & Steam ML-122D Retain This Manual In A Safe Place For Future Reference“IMPORTANT NOTE TO PURCHASER” FOR YOUR SAFETY The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONALINJURY OR FIRE COULD RESULT SECTION Table of ContentsSPECIFICATIONS/COMPONENT IDENTIFICATION SECTIONPROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT BURNER AND BASKET TUMBLER/LINT CHAMBER MANUAL RESETREVERSING TIMER SPIN/DWELL ADJUSTMENTS A. CleaningSECTION IMPORTANT INFORMATIONB. SAFETY PRECAUTIONS EXPLOSION COULD RESULTEXPLOSION COULD RESULT WARNING PERSONAL INJURY OR FIRE COULD RESULT STANDARDSSPECIFICATIONS/COMPONENT IDENTIFICATION SECTIONSteam Specifications MLG-122 Gas MLS-122 Steam 1 Microprocessor Control/Keyboard Touch Pad Panel Assembly Controls 2 Control Top Access Door Assembly 3 Main Door Assembly4 Lint Panel Assembly 5 Lint Drawer 6 Wire Diagram Located Behind Control Door1 Electrical Service Connections 2 Top Console 3 Heating Unit 4 Relay/Wiring Box 5 Data Label and Installation Label2. Dryer Rear View Illus. NoINSTALLATION PROCEDURES SECTIONA. LOCATION REQUIREMENTS B. UNPACKING/SETTING UP 1 Disconnect the ground wire A at the rear of dryer C. DRYER ENCLOSURE REQUIREMENTS D. FRESH AIR SUPPLY REQUIREMENTS E. EXHAUST REQUIREMENTS a. Outside Ductwork Protection a. Ducting Horizontal and Vertical b. Outside Ductwork Protection b. Outside Ductwork Protection F. ELECTRICAL INFORMATION ELECTRICAL SERVICE SPECIFICATIONS PER DRYER SERVICEWIRE FUSINGNOTE A CIRCUIT SERVICING EACH DRYER MUST BE PROVIDED G. GAS INFORMATION WARNING FIRE OR EXPLOSION COULD RESULTTYPE OF GAS TYPE OF GAS8.7 mb 26.1 mbWARNING NEVER TEST FOR LEAKS WITH A FLAME Page OPERATING STEAM PRESSURE H. STEAM INFORMATION862 kPa 689 kPaa. The pressure of the condensate in the steam supply will cause water hammer and subsequent heat exchanger steam coil failure. The steam supply connection into the main supply line must be made with a minimum 12-inch 30.48 cm riser. This will prevent any condensate from draining towards the dryer COMPRESSED AIR PRESSUREAIR SUPPLY Normal6. Steam Damper Air Piston Flow Control Operation Adjustment COMPRESSED AIR PRESSUREAIR SUPPLY NormalK. PREOPERATIONAL TESTS Natural Gas b. Dual Timer Check Heating Timer Cool Down Timer Temperature Selection SwitchBASKET COATING 9. Make a complete operational check of ALL operating controlsL. OPERATING INSTRUCTIONS M. SHUT DOWN INSTRUCTIONS a. GAS MODELS...discontinue the gas supply1 SHUT OFF external gas supply shutoff valve b. STEAM MODELS...discontinue the steam supplySERVICE/PARTS INFORMATION A. SERVICESECTION B. PARTSWARRANTY INFORMATION A. RETURNING WARRANTY CARDSB. WARRANTY C. RETURNING WARRANTY PARTS2. Each part must be tagged with the following information ROUTINE MAINTENANCE A. CLEANINGELECTRICAL POWER SUPPLY TO THE DRYER SECTIONNOTE Replace in matched sets both belts B. ADJUSTMENTS 7 DAYS AFTER INSTALLATION AND EVERY 6 MONTHS THEREAFTERC. LUBRICATION REVERSING TIMER SPIN/DWELL ADJUSTMENTS Adjustment Position NumberTime in Seconds 10.2PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS SECTION1 “FAN” Blower output light emitting diode L.E.D. indicator 2 “FOR” Forward output L.E.D. indicator3 “Rev” Reverse output L.E.D. indicator 4 “Air” Air Jet output L.E.D. indicatorf. Try to restart the dryer with the main door open b. Starting the drying cycle i. Functional check of the DSI module is completeDATA LABEL INFORMATION SECTIONA. DATA LABEL Contact American Dryer Corporation7. ELECTRIC SERVICE THE DATA LABEL 1. MODEL NUMBER2. SERIAL NUMBER 3. MANUFACTURING CODE NUMBERMANUAL RESET HI-LIMIT INSTRUCTIONS BURNER AND BASKET TUMBLER/LINT CHAMBERWARNING Discontinue power to dryer before attempting to reset hi-limit1 - 02/16/00-15 2 - 11/10/00-103 * 08/13/01-25