Manuals / American Dryer Corp / Laundry Appliance / Clothes Dryer

American Dryer Corp ML-122D Dryer Rear View, Illus. No, Description, Air Connection

Models: ML-122D

1 55

Download 55 pages 50.3 Kb

Page 13

2.Dryer Rear View

2.Dryer Rear View

Illus. No.

Description

1Electrical Service Connections

2Top Console

3Heating Unit

4Relay/Wiring Box

5Data Label and Installation Label

6Air Connection

9

Image 13

American Dryer Corp ML-122D Dryer Rear View, Illus. No, Description, Relay/Wiring Box 5 Data Label and Installation Label

Contents

ML-122D Installation ManualGas & Steam Retain This Manual In A Safe Place For Future Reference ML-122D“IMPORTANT NOTE TO PURCHASER” FOR YOUR SAFETY The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONALINJURY OR FIRE COULD RESULT Table of Contents SECTIONSPECIFICATIONS/COMPONENT IDENTIFICATION SECTIONBURNER AND BASKET TUMBLER/LINT CHAMBER MANUAL RESET PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENTREVERSING TIMER SPIN/DWELL ADJUSTMENTS A. CleaningIMPORTANT INFORMATION SECTIONEXPLOSION COULD RESULT B. SAFETY PRECAUTIONSEXPLOSION COULD RESULT STANDARDS WARNING PERSONAL INJURY OR FIRE COULD RESULTSECTION SPECIFICATIONS/COMPONENT IDENTIFICATIONSteam Specifications MLG-122 Gas MLS-122 Steam 2 Control Top Access Door Assembly 3 Main Door Assembly 1 Microprocessor Control/Keyboard Touch Pad Panel Assembly Controls4 Lint Panel Assembly 5 Lint Drawer 6 Wire Diagram Located Behind Control Door4 Relay/Wiring Box 5 Data Label and Installation Label 1 Electrical Service Connections 2 Top Console 3 Heating Unit2. Dryer Rear View Illus. NoSECTION INSTALLATION PROCEDURESA. LOCATION REQUIREMENTS B. UNPACKING/SETTING UP 1 Disconnect the ground wire A at the rear of dryer C. DRYER ENCLOSURE REQUIREMENTS D. FRESH AIR SUPPLY REQUIREMENTS E. EXHAUST REQUIREMENTS a. Outside Ductwork Protection a. Ducting Horizontal and Vertical b. Outside Ductwork Protection b. Outside Ductwork Protection F. ELECTRICAL INFORMATION SERVICE ELECTRICAL SERVICE SPECIFICATIONS PER DRYERWIRE FUSINGNOTE A CIRCUIT SERVICING EACH DRYER MUST BE PROVIDED WARNING FIRE OR EXPLOSION COULD RESULT G. GAS INFORMATIONTYPE OF GAS TYPE OF GAS8.7 mb 26.1 mbWARNING NEVER TEST FOR LEAKS WITH A FLAME Page H. STEAM INFORMATION OPERATING STEAM PRESSURE862 kPa 689 kPaa. The pressure of the condensate in the steam supply will cause water hammer and subsequent heat exchanger steam coil failure. The steam supply connection into the main supply line must be made with a minimum 12-inch 30.48 cm riser. This will prevent any condensate from draining towards the dryer AIR PRESSURE COMPRESSEDAIR SUPPLY Normal6. Steam Damper Air Piston Flow Control Operation Adjustment AIR PRESSURE COMPRESSEDAIR SUPPLY NormalK. PREOPERATIONAL TESTS Natural Gas Heating Timer Cool Down Timer Temperature Selection Switch b. Dual Timer CheckBASKET COATING 9. Make a complete operational check of ALL operating controlsL. OPERATING INSTRUCTIONS a. GAS MODELS...discontinue the gas supply M. SHUT DOWN INSTRUCTIONS1 SHUT OFF external gas supply shutoff valve b. STEAM MODELS...discontinue the steam supplyA. SERVICE SERVICE/PARTS INFORMATIONSECTION B. PARTSA. RETURNING WARRANTY CARDS WARRANTY INFORMATIONB. WARRANTY C. RETURNING WARRANTY PARTS2. Each part must be tagged with the following information A. CLEANING ROUTINE MAINTENANCEELECTRICAL POWER SUPPLY TO THE DRYER SECTIONNOTE Replace in matched sets both belts 7 DAYS AFTER INSTALLATION AND EVERY 6 MONTHS THEREAFTER B. ADJUSTMENTSC. LUBRICATION Adjustment Position Number REVERSING TIMER SPIN/DWELL ADJUSTMENTSTime in Seconds 10.2SECTION PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS2 “FOR” Forward output L.E.D. indicator 1 “FAN” Blower output light emitting diode L.E.D. indicator3 “Rev” Reverse output L.E.D. indicator 4 “Air” Air Jet output L.E.D. indicatorf. Try to restart the dryer with the main door open i. Functional check of the DSI module is complete b. Starting the drying cycleSECTION DATA LABEL INFORMATIONA. DATA LABEL Contact American Dryer CorporationTHE DATA LABEL 1. MODEL NUMBER 7. ELECTRIC SERVICE2. SERIAL NUMBER 3. MANUFACTURING CODE NUMBERBURNER AND BASKET TUMBLER/LINT CHAMBER MANUAL RESET HI-LIMIT INSTRUCTIONSWARNING Discontinue power to dryer before attempting to reset hi-limit2 - 11/10/00-10 1 - 02/16/00-153 * 08/13/01-25