®
www.apc.com
Back-UPS HS 500
User’s Manual
NOTE: APC recommends your network equipment (computer, modem, router, hub, or other networked devices) be completely installed, configured, and tested prior to adding this UPS to the network.
INSTALLATION
1 Placement | 2 Remove Connector Cover | 3 Remove Battery (if |
32 - 104oF (0 - 40oC)
|
|
|
|
| Press cover release | Remove battery. |
| ||||||
| ||||||
|
|
|
|
| tab (one each side) |
|
Press the outlet cover release |
|
|
| and remove cover. |
| |
|
| Disconnect battery | ||||
| ||||||
tab (one each side); and pivot | ||||||
cover off the unit. |
|
| wires from battery. | |||
| ||||||
| ||||||
|
|
|
|
|
| Caution: To prevent damage to the ribbon cable (not shown) |
|
|
|
|
|
| that connects the cover to the UPS, replace the cover after |
|
|
|
|
|
| removing the battery. Do not disconnect the ribbon cable |
|
|
|
|
|
| from the cover or the UPS. |
4Mount Back-UPS (optional)
Wall Anchor
Mounting
Hole
5Connect and Install Battery, Install Battery Cover
6Connect Cable Modem, 7 Connect Phone Line
DSS or CATV Receiver | or DSL to Surge |
to Surge Protection | Protection (optional) |
(optional) | Modem/Phone/Fax Network |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Cable In Cable Out Circuit Breaker | ® |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||||||
|
|
|
|
|
| Push to Reset |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||
|
|
|
|
|
|
|
| w w w.apc.com |
|
|
|
|
| Connectors |
|
|
|
| Connectors | |||||||||||||||||||||||
|
|
|
| Input: |
|
| ||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| 120V~, 10A, |
|
|
|
| (will accept |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||
Wall
Press the outlet cover release tab (one each side); and pivot cover off the unit.
Install battery cover.
Connect and install
the battery..
|
|
| To Hub or |
|
|
| Router |
From Cable Provider | To Cable Modem, |
|
|
(Phone, Internet, | VCR, DSS or TV |
|
|
and/or CATV; or | Cable Box | Phone Line In | From Modem |
DSS) |
| (Standard or | |
|
| DSL) | Phone Line Out |
|
|
|
8Connect Network Equipment
LANFrom Network Device
(or Computer Using a
Crossover Cable)
9Connect Equipment Power Cords
| Network Device |
Hub |
|
or Router | Output 3 |
Output 1 | Network Device |
| |
| Modem | Output 3 |
| |
Output 2 |
|
10Install Connector Cover
Align the holes in the cover with the connector cover release tabs (one each side) and lower connector cover.
11Connect to Power Source and Switch on UPS Power
12Check the Building Wiring Fault Indicator
Check the Building Wiring Fault indicator. If this light emitting diode (LED) is illuminated, it is an indication that a potential shock hazard exists. Have the building wiring inspected and repaired by a qualified electrician.
Building WiringFault Indicator
