American Standard 2775.XXXW Series installation instructions Xxxw Series Whirlpool, Cadet Corner

CADET™ CORNER

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

2775.XXXW SERIES WHIRLPOOL

INSTALLATION INSTRUCTIONS

165mm (6-1/2)

RECOMMENDED FITTING LOCATION

64 X 330mm (2-1/2 X 13)

OUTLINE OF

CUTOUTC/L

1080 mm

(42-1/2)

2159mm

(85)

1080mm	229 X 305mm
	(9 X 12)
(42-1/2)	CUTOUT IN
	FLOOR FOR
	DRAIN	1076mm
	SAFE-T-	(42-3/8)
	HEATER		1524mm
	REMOVABLE
	BLANK		(60)
70mm REF.	ON/OFF
(2-3/4)	SWITCH
		PROVIDE ACCESS
		TO PUMP FOR
		SERVICING ON ALL
	PUMP	INSTALLATIONS

279mm

(11)

C/L OF

DRAIN OUTLET

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

List of Optional Components (not included):

•Safe-T-Heater 9075.120*

•Tile Bead Kit 751755-100*

* see your American Standard Dirstributor

	C/L OF	76mm	LEVELING STRINGER
		(3)	NOT FOR SUPPORT
38 mm REF.	OVERFLOW
(1-1/2)
				502mm
				(19-3/4)
INTEGRAL				464mm
				(18-1/4)
SUPPORT
FEET
ROUGH	1-1/2 N.P.T.M.
FLOOR	THREADS			117mm
			70mm
	1-1/2 O.D. TAILPIECE			(4-5/8)
			(2-3/4)

List of Required Components (not included):

• Drain* 1583.470	• Bath Filler*
* see your American	Standard Dirstributor

GENERAL SPECIFICATIONS FOR 2775 WHIRLPOOL

INSTALLED SIZE		85 X 60 X 19-3/4In.(2159 X 1524 X 502mm)
WEIGHT						130 Lbs. (59 Kg.)
WEIGHT w/WATER					756 Lbs. (343 Kg.)
GAL. TO OVERFLOW							75 Gal. (284 L.)
MIN. OPERATING GAL.							60 Gal. (227 L.)
BATHING WELL AT SUMP			32 X 32 In. (813 mm X 813 mm)
BATHING WELL AT RIM				46 X 46 In. (1168 X 1168mm)
WATER DEPTH TO OVERFLOW							14 In. (356 mm)
FLOOR LOADING			34 Lbs./Sq. Ft. (115 Kgs/Sq. m.)
(PROJECTED AREA)
PTS.								41.7
CUBE	(FT3)							70.4

WHIRLPOOL ELECTRICAL SPECIFICATIONS

SYSTEM I PUMP 2.1 HP, 14.4 AMPS, 120V.

GENERAL INSTALLATION INFORMATION

List of Required Tools and Supplies:

Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 3 or 2 x 2
•	Screw Driver		Stringers
•	Standard	•	Drop Cloth
	Woodworking Tools	•	20 amp GFI
•	Personal Safety		Outlet
	Equipment	•	Cement, Plaster,
•	Caulking Gun		Grout

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2003

752536-100 Rev. GAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.