American Standard 3475.5 Bidet Faucet and Transfer Valve, with SpeedConnect Drain, 3475.301

Installation

Instructions

COLONY/COLONY SOFT	3475.301
Bidet Faucet and Transfer Valve	3475.501

with SpeedConnect™ Drain

Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets.

SpeedConnect Drain*•Fewer parts, installs in less time

•Never needs adjustment

•Guaranteed to seal properly the first time, every time.

Certified to comply with ANSI A112.18.1

M968796 Rev. 1 . 1

*Your new American Standard faucet is designed to work only with the SpeedConnect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Roughing-in Dimensions					8 TO 12
	TRANSFER VALVE		FINISHED
			WALL
	(FOR FLUSHING
BIDET OUTLINE	RIM OR SPRAY)
				(C)	(H)
IS SYMBOLIC	7/8 DIA.
DOUCHE ADJ. 1-1/4				1-3/16 DIA.
		2-1/8		1-1/4 MAX.
SPRAY	TO 2-1/4	DIA.
3-7/8	1-3/8
	DIA.
				FINISHED
	5-1/2			FLOOR
			1-1/4 O.D. TAILPIECE

DIVERTER AND

VACUUM BREAKER

ASSEMBLY

2-1/4 DIA.

4-1/4

FOR GROUND JOINT CONNECTION OR 1/2 " O.D. SLIP (INLETS)

REAR VIEW WITH

WALL REMOVED

Required tools

Screwdriver	Plumbers' Putty or
	Caulking
Phillips Screwdriver
	Channel Locks

Adjustable Wrench

Tubing Cutter

1			Turn off hot and cold water
	BIDET FAUCET INSTALLATION	CAUTION
			supplies before beginning.
	Place RUBBER RING (10) into ADAPTER (4).
	Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From
	under side of mounting surface, install VALVE BODY (3, 3a) through valve mounting			4
	holes. Threads of VALVE BODY (3, 3a) should extent at least 5/16 of a inch above
	mounting surface top. Fig. A. Thread ADAPTER (4) onto VALVE BODIES (3, 3a)			10
	until snug against internal stop. If necessary, adjust LOCKNUT (1).

11

6

7

BIDET

LEDGE

Tighten LOCKNUTS (1) with WRENCH (5) (supplied) to secure VALVE BODIES (3, 3a).

Remove MOUNTING NUT (6), WASHER (7) and UPPER GASKET (8) from TRANSFER VALVE (9). Insert TRANSFER VALVE (9) into the center forward hole of BIDET.

Replace UPPER GASKET (8) and WASHER (7) . Position the side threaded outlet rearward and secure MOUNTING NUT (6). Thread ESCUTCHEON (11) onto TRANSFER VALVE (9) until it seats against the BIDET LEDGE.

Fig. A.	4
	10
5/16''	MOUNTING
MIN.
	SURFACE
		2
	2	1
	1
3, 3a		5

	3	3a
HOT		COLD

8

9

2 SPRAY INSTALLATION

8	2	9
7	PUTTY	1

Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside of SPRAY BODY FLANGE (2) and secure with NUT (3).

6

3

Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1). Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet NIPPLE (7) of the TRANSFER VALVE (8).

Thread SPRAY CAP (9) onto SPRAY BODY (1).

4	5
	4

1