American Standard 751711-100 installation instructions Cadenza, Thank You, Tools, Supplies

CADENZA™

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

6060.XXXWSERIES

WHIRLPOOL

INSTALLATION INSTRUCTIONS

1949mm (76-3/4 REF.)

975mm

(38-3/8)

1661mm

(65-3/8)

OUTLINE OF	C/L
CUTOUT
	SEAT AREA
	178mm x 381mm
	(7 x 15) CUTOUT

1384mm
(54	1605mm
-
1/2)	(63
	-
	3/16)

PUMP

PROVIDE ACCESS TO PUMP FOR SERVICE ON ALL INSTALLATIONS NOTE: APRON ASSEMBLY WILL PROVIDE REQUIRED ACCESS FOR SERVICING

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

346mm				ON/OFF SWITCH
(13-5/8)
			RECOMMENDED FITTING
143mm		254mm	LOCATION 64 X 381mm (2-1/2 X 15)
	C/L OF
(5-5/8)		(10)
	DRAIN
		114mm
				LEVELING STRINGER
C/L OF OVERFLOW		(4-1/2)
				NOT FOR SUPPORT
89mm
(3-1/2)		E-Z-Install™ HEATER
83mm				495mm
				(19-1/2)
(3-1/4)
			51mm
			(2)	546mm
38mm				(21-1/2)
(1-1/2)			INTEGRAL FEET
			SUPPORT
		1-1/2 N.P.T. THREAD	ROUGH FLOOR
		1-1/2 O.D. TAILPIECE

GENERAL SPECIFICATIONS FOR 6060 WHIRLPOOL

INSTALLED SIZE		76-3/4 x 65-3/8 x 21-1/2 In. (1949 x 1661 x 546mm)
WEIGHT						105 Lbs. (48 Kg.)
WEIGHT w/WATER						822 Lbs. (370 Kg.)
GAL. TO OVERFLOW							86 Gal. (326 L)
WHIRLPOOL MIN. OPERATING VOL.							71 Gal. (269 L)
BATHING WELL AT SUMP				45 x 40 In. (1143 x 1016mm)
BATHING WELL AT RIM				49 x 43 In. (1245 x 1092mm)
WATER DEPTH TO OVERFLOW						15-3/8 In. (391mm)
FLOOR LOADING			24 Lbs./Sq.Ft. (114 Kgs./Sq.m)
(PROJECTED AREA)
PTS.								41.7
CUBE (FT3)								68.4
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM II PUMP					2.1 HP, 15.6 AMPS,120V.

List of Optional Components (not included):

•Apron Kit 0707.200*

•Tile Bead Kit 751755-100*

List of Required Components (not included):

•	Drain 1583.470*		• Bath Filler*
* see your American Standard Distributor
List of Required Tools and Supplies:
Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	• 1 x 3 or 2 x 2 Stringers
•	Screw Driver	•	Drop Cloth

•Standard Woodworking Tools • 20 amp GFI Outlet

•Personal Safety Equipment • Cement, Plaster, Grout

•Caulking Gun

GENERAL INSTALLATION INFORMATION

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2007

751711-100 REV. GAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.