
Quick Start Guide
MVP-7500 Modero Wireless Touch Panel (Firmware version G4)
For more detailed installation, configuration, programming, file transfer, and operating instructions refer to the
FIG. 1 MVP-7500 Wireless Touch Panel (FG5965-01)
ATTENTION!
Verify the NetLinx Master Firmware is build 117 or greater for the ME260 and
Overview
The AMX
MVP-7500 Panels Specifications (Cont.)
Panel LCD | • | Panel type: TFT Color |
Parameters: | • | Aspect ratio: 4 x 3 |
| • | Brightness: 120 cd/m2 |
| • Channel transparency: | |
| • | Contrast ratio: 20:1 |
| • Display colors: 4096 colors | |
| • Dot/pixel pitch: 0.23 mm | |
| • | Screen Resolution: 640 x 480 pixels (HV) @ 60 Hz frame frequency |
|
|
|
External | • | Docking Station Interface Connector: Metallic strip connector located |
Components: |
| on the bottom of the MVP provides communication and power between |
|
| the MVP and the optional docking station. |
| • | LEDs: Two sets of NetLinx programmable LEDs (support On, Off, |
|
| and Blink). |
| • | |
|
| and touch panel file transfer to and from the PC. |
| • Stylus slot: Illuminated slot where the included stylus can be stored, | |
|
| located on the left side of the MVP. |
| • | Power Connector: 6mm |
|
| cord from the PS4.4 power supply (included). |
|
|
|
Internal | • | Wireless Interface card: Provides 802.11b (Type I) wireless connectivity |
Components: |
| between the panel and a Wireless Access Point (WAP). |
| • IR Emitters: Transmit IR over 20 feet (6.10 m) from the panel. | |
| • Internal Buzzer: Emits a Piezo electric tone. | |
| • | Battery Compartment: Houses up to two |
|
| |
|
|
|
External Buttons: | • | Nine external programmable pushbuttons (four located on the left of the |
|
| LCD and five located on the right) |
| • All of these buttons are | |
|
| commands |
|
|
|
Power Modes: | • | ON: Panel is fully functional. |
| • | STANDBY: Panel uses low power, the LCD/backlight is shutdown, |
|
| LEDs still function. Panel resumes the ON mode in ~ 1 second. |
| • OFF: | |
|
| not functional. Panel resumes the ON mode in ~ 30 seconds. |
|
|
|
Operating/Storage | • | Operating Temperature: 0° C (32° F) to 40° C (104° F) |
Environments: | • | Operating Humidity: 20% - 85% RH |
| • Storage Temperature: | |
| • Storage Humidity: 5% - 85% RH | |
|
|
|
Included | • | |
Accessories |
| Quick Start Guide |
| • | |
| • PS4.4 Power Supply (13.5 VDC) | |
| • | Stylus |
|
|
|
Optional | • | |
Accessories: | • | |
| • | |
| • |
User programmable |
| |
pushbuttons (9) |
|
|
User
programmable Stylus LED (side panel)
Stylus (fits within
slot on side panel)
FIG. 2 MVP-7500 Touch Panel component locations
Specifications
User programmable status LED
(front panel)
PWR connector
Docking station interface connector
• | |
• | |
• | |
• | Upgrade Compact Flash (factory programmed with firmware): |
| |
| |
| |
|
Connections and Wiring
The PS4.4 Power Supply (with barrel connector) provides power to the
•Once the MVP is connected to a docking station; charging priority is first given to any
Dimensions (HWD): | • | 7.09" x 10.47" x 1.47" (18.00 cm x 26.60 cm x 3.73 cm) |
|
|
|
Power: | • | Full draw: 1.0 A @ 12 VDC |
| • | Full On and charging up to two |
|
|
|
Battery Duration: | • | 4 hours Normal use (25% On state, 25% Standby, and 50% Sleep). |
(per battery) | • | 2 hours Continuous use (continuous On state). |
|
| |
Memory: | • 64 MB SDRAM | |
| • | 64 MB Compact Flash (upgradable to 1 GB) - factory programmed |
|
|
|
Weight: | • | |
| • Panel with one battery: 2.25 lbs (1.02 kg) | |
| • Panel with two batteries: 2.65 lbs (1.20 kg) | |
|
|
|
Screen Resolution: | • | 640 x 480 pixels (HV) @ 60 Hz frame frequency |
|
|
|
Viewing Angle: | • | Horizontal: + 55° (left and right) from center |
| • Vertical: + 25° (up from center) and | |
|
|
|
USB Connection
This panel uses a standard version 1.1 Type A to
WARNING: Although firmware upgrades can be done over wireless Ethernet; it is strongly recommended that firmware KIT files be transferred over a direct USB connection and only when the panel is connected to a power supply. If battery power or wireless connection fails during a firmware upgrade, the panel flash file system may become corrupted.