AMX RE-DM4, RE-DM6 manual

Operation/Reference Guide

Lighting Controls

Radia Eclipse Dimmer

Modules

RE-DM4

RE-DM6

Last Revised: 9/29/2011

Contents

Main AMX Limited Warranty and Disclaimer Page Page Table of Contents Radia Lighting System Configuration Pages ..................................................... 25 AMX RADIA Lighting Programming .................................................................31 Page Page Radia Eclipse Dimmer Modules Radia Eclipse RE-DM4 Dimmer Module RE-DM4 Specifications Suggested Loads RE-DM4 Specifications Dimmed Switched Caution: Pre-Installation Notes RE-DM4 4-pin module connector (male) Line-In Connections RE-DM4 Lighting Application Drawings The RE-DM4 has two preferred lighting application methods, as shown in FIG.4 and FIG. 5: Please refer to the AMX RADIA Lighting Programming section on page 31 for more information. Radia Eclipse RE-DM6 Dimmer Module RE-DM6 Specifications Suggested Installation Loads RE-DM6 Specifications Dimmed Switched Caution: Pre-Installation Notes Line-In Connections RE-DM6 Lighting Application Drawings AMX Lighting Systems Features Applications AMX Lighting Control Equipment AMX Lighting Control Equipment (Cont.) Installation Space Requirements Wiring Considerations Preparing/connecting captive wires 1. 2. AxLink wiring between multiple devices Conduit Installation 13 RE-DM4 and RE-DM6 RADIA Eclipse Dimmer Modules RDA Enclosure Dimensions FIG. 13 RDA-ENC2, -ENC4, and -ENC6 enclosure and dimensions FIG. 13 shows the dimensions for the RDA-ENC6B and RDA-ENC12B enclosures. FIG. 12 shows the dimensions for the RDA-ENC2, RDA-ENC4, and RDA-ENC6 enclosures. Mounting AMX Lighting Enclosures 1. 2. 3. 4. 5. High-Voltage Connections Connecting High-Voltage, Single-Phase Input Power and Loads 1. 2. 3. 4. RDA-ENC6B 120 VAC Single Phase Line Input RDA-ENC6B 120/240 VAC Line Input (Single Phase) Connecting High-Voltage Input Power and Loads Page RDA-ENC6B Three Phase Line Input Connector Reference FIG. 21 shows a sample RDA-ENC6 three phase (4 W + G) line input connector and dimmer references. FIG. 22 shows the power distribution and line input references for the RDC-PFC line inputs. RDC-PFC Power Distribution And Line Input References Installing RDM Modules Into an RDA Enclosure Low-Voltage Connections Module Connections Green LED Status Indicator Red LED Status Indicators (RE-DM4 only) Configuring and connecting multiple controllers 1. 2. Configuring and Connecting AxLink 1. 2. 3. 4. 5. External power Dry Closures Connecting Dry Closures Failsafe Input Emergency Input Default Settings Default preset time values Default Presets Radia Lighting System Configuration Pages Lighting System Link 1. 2. 3. 4. Main Lighting System Page Device Configuration Page Page Page 6. 7. AMX RADIA Lighting Programming Software Presets: Defined vs. Undefined Levels Preset Status g Meetin Lighting Systems Overview Programming Commands Setup commands Recording commands Status commands Operation commands Levels Default Settings Default Low-end Default Ramp Time Initial Level Status Reporting Channels SEND_STRINGs Ramp Dimmers Up carriage return with the string. Ramp Dimmers Down This function ramps down the specified dimmer(s) until the ramping stops or the dimmer(s) reach 0%. send the carriage return with the string. Stop Ramping Dimmer Ramp Active Preset Up Ramp Active Preset Down Stop Ramping Preset Recall Preset Record Preset Level Status Set Curve Curve Status Set Low End Low End Status Dimmer Status Reboot Set Default Level Time Set Default Preset Time Set Default Ramp Time Ramp To Level Undefine Dimmer Phase Query Version Query Factory Default SEND_COMMANDs Ramp Preset Up (NEW) Ramp Preset Down (NEW) Stop Ramping Preset (NEW) Recall Preset Record Preset Set Curve Curve Status (NEW) Set Low End (NEW) Low End Status (NEW) Reboot (NEW) Set Default Level Time Set Default Preset Time Set Default Ramp Time Ramp to Level Undefine Dimmer (NEW) Phase Query (NEW) Appendix A: AMX Lighting Curves Page Curve Configuration Curves The following table provides a general relationship between load type and which curve to use: Standard Dimming Curve (1) FIG. 39 shows the curve 1 voltage output in 120 volts DC. Load Type Curves Page Economical Dimming Curve (2) 0-10VDC Curve (3) Page 0-12VDC Curve (4) Lutron FDB Curve (5) Page Advance Mark VII Curve (6) 12% Roll Off (7) Page 19% Roll Off (8) 33% Roll Off (9) Page S-Curve #1 (A) Log-Curve #1 (B) Page Log-Curve #2 (C) S-Curve #2 (D) 10% Off Curve (N) Always OFF Curve (O) Always ON Curve (F) Page Page Page Page Page Appendix B: Troubleshooting Software Issues Using PASS mode 1. 2. Hardware Issues Troubleshooting hardware