Analog Devices manual AD600/AD602, Function, Description

AD600/AD602

ABSOLUTE MAXIMUM RATINGS1

Supply Voltage ± VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 7.5 V

Input Voltages

Pins 1, 8, 9, 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± VS Pins 2, 3, 6, 7 . . . . . . . . . . . . . . . . . . . . . . . ± 2 V Continuous

. . . . . . . . . . . . . . . . . . . . . . . . . ± VS for 10 ms Pins 4, 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± VS Internal Power Dissipation2 . . . . . . . . . . . . . . . . . . . . 600 mW

Operating Temperature Range (J) . . . . . . . . . . . 0°C to +70°C Operating Temperature Range (A) . . . . . . . . .–40°C to +85°C Operating Temperature Range (S) . . . . . . . . . –55°C to +125°C Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300°C

NOTES

1Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

2Thermal Characteristics: 16-Pin Plastic Package: θJA = 85°C/Watt 16-Pin SOIC Package: θJA = 100°C/Watt

16-Pin Cerdip Package: θJA = 120°C/Watt

ORDERING GUIDE

	Gain	Temperatue	Package
Model	Range	Range	Option1
AD600AQ	0 dB to +40 dB	–40°C to +85°C	Q-16
AD600AR	0 dB to +40 dB	–40°C to +85°C	R-16
AD602AQ	–10 dB to +30 dB	–40°C to +85°C	Q-16
AD602AR	–10 dB to +30 dB	–40°C to +85°C	R-16
AD600JN	0 dB to +40 dB	0°C to +70°C	N-16
AD600JR	0 dB to +40 dB	0°C to +70°C	R-16
AD602JN	–10 dB to +30 dB	0°C to +70°C	N-16
AD602JR	–10 dB to +30 dB	0°C to +70°C	R-16
AD600SQ/883B2	0 dB to +40 dB	–55°C to +150°C	Q-16
AD602SQ/883B3	–10 dB to +30 dB	–55°C to +150°C	Q-16

NOTES

1N = Plastic DIP; Q= Cerdip; R= Small Outline IC (SOIC).

2Refer to AD600/AD602 Military data sheet. Also available as 5962-9457201MPA. 3Refer to AD600/AD602 Military data sheet. Also available as 5962-9457202MPA.

			PIN DESCRIPTION
Pin	Function		Description
Pin 1	C1LO		CH1 Gain-Control Input “LO” (Positive
			Voltage Reduces CH1 Gain).
Pin 2	A1HI		CH1 Signal Input “HI” (Positive Voltage
			Increases CH1 Output).
Pin 3	A1LO		CH1 Signal Input “LO” (Usually Taken to
			CH1 Input Ground)
Pin 4	GAT1		CH1 Gating Input (A Logic “HI” Shuts Off
			CH1 Signal Path).
Pin 5	GAT2		CH2 Gating Input (A Logic “HI” Shuts Off
			CH2 Signal Path).
Pin 6	A2LO		CH2 Signal Input “LO” (Usually Taken to
			CH2 Input Ground).
Pin 7	A2HI		CH2 Signal Input “HI” (Positive Voltage
			Increases CH2 Output).
Pin 8	C2LO		CH2 Gain-Control Input “LO” (Positive
			Voltage Reduces CH2 Gain).
Pin 9	C2HI		CH2 Gain-Control Input “HI” (Positive
			Voltage Increases CH2 Gain).
Pin 10	A2CM		CH2 Common (Usually Taken to CH2
			Output Ground).
Pin 11	A2OP		CH2 Output.
Pin 12	VNEG		Negative Supply for Both Amplifiers.
Pin 13	VPOS		Positive Supply for Both Amplifiers.
Pin 14	A1OP		CH1 Output.
Pin 15	A1CM		CH1 Common (Usually Taken to CH1
			Output Ground).
Pin 16	C1HI		CH1 Gain-Control Input “HI” (Positive
			Voltage Increases CH1 Gain).
	CONNECTION DIAGRAM
	16-Pin Plastic DIP (N) Package
	16-Pin Plastic SOIC (R) Package
		16-Pin Cerdip (Q) Package
	C1LO			1			16	C1HI
	A1HI							A1CM
				2		A1	15
	A1LO			3			14	A1OP
	GAT1							VPOS
				4		REF	13
	GAT2							VNEG
				5			12
	A2LO							A2OP
				6		A2	11
	A2HI							A2CM
				7			10
	C2LO			8	AD600/AD602		9	C2HI

CAUTION

ESD (electrostatic discharge) sensitive device. Permanent damage may occur on unconnected devices subject to high energy electrostatic fields. Unused devices must be stored in conductive foam or shunts. The protective foam should be discharged to the destination socket before devices are removed.

WARNING!

ESD SENSITIVE DEVICE

REV. A –3–