Manuals / Advantech / Computer Equipment / Computer Hardware

Advantech 2006957006 5th Edition user manual D.4 IRQ mapping chart, SCSI IRQ select 9, 11, 12

Models: 2006957006 5th Edition

1 128

Download 128 pages 42.83 Kb

Page 120

Image 120

D.4 IRQ mapping chart

Table D-4: IRQ mapping chart

0	Interval timer
1	Keyboard

2	Interrupt from Controller 2

3	COM2

4	COM1

5	COM4

6	FDD

7	LPT1

8	RTC

9	Reserved

10	COM3

11	Reserved (watchdog timer)

12	PS/2 mouse

13	INT from co-processor

14	Primary IDE

15	Secondary IDE (reserved for CompactFlash)

*Ethernet interface IRQ select: 9, 11, 12, 15

*PnP USB IRQ select: 9, 11, 12, 15

*SCSI IRQ select: 9, 11, 12, 15

108 PCM-9570/S User's Manual

Page 120

Image 120

Advantech 2006957006 5th Edition user manual D.4 IRQ mapping chart, SCSI IRQ select 9, 11, 12

Contents

PCM-9570/S Socket 370 Celeron/Pentium III SBC with LCD, Ethernet and SCSIUsers Manual Copyright notice Acknowledgments Packing list Please refer to Appendix E for the optional interface wiring kit1 PCM-9570/S all-in-one single board computer 1 CD disc with utility and drivers 1 Startup ManualContents Chapter 2 InstallationChapter 1 General Information 2.10 Chapter 3 Software Configuration Chapter 4 Award BIOS SetupChapter 5 PCI SVGA Setup Chapter 6 SCSI Setup and Configurations TimerAppendix B Installing PC/104 Modules Chapter 7 PCI Bus Ethernet InterfaceAppendix D System Assignments Appendix E Optional ExtrasAppendix F Mechanical Drawings E.1 PCM-10586-4 cable kit for PCM-9570/STables Table C-19 COM2 port for RS-232, RS-422 and RS-485 CN20Table C-20 CompactFlash card connector CN21 Table C-21 PanelLink connector CN22Table C-22 Fan power connector FAN1 Table D-4 IRQ mapping chartFigures Figure F-1 PCM-9570/S mechanical drawing - component sideFigure F-2 PCM-9570/S mechanical drawing - solder side General Information Sections include Introduction Features SpecificationsBoard layout and dimensions This chapter gives background information on the PCM-9570/S1.1 Introduction Highly integrated Socket 370 SBC1.2 Features 1.3 SpecificationsStandard SBC functions PCI SVGA/flat panel interface Display modePCI bus Ethernet interface Ultra2 SCSI PCM-9570S onlySolid state disk PanelLink optional1.4 Board layout and dimensions Figure 1-1 PCM-9570/S dimensions6 PCM-9570/S Users Manual Installation C H A P T E R2.1 Jumpers LabelFunction 2.2 Connectors Please refer to Appendix C for pin assignmentsLabel Function2.3 Locating jumpers Figure 2-1 Locating jumpers10 PCM-9570/S Users Manual 2.4 Locating connectors 2.4.1 Component sideFigure 2-2 Locating connectors component side Chapter 2 Installation2.4.2 Solder side Figure 2-3 Locating connectors solder side12 PCM-9570/S Users Manual 2.5 Setting jumpers 2.6 CPU installation and upgrading 2.6.1 Installing a CPU in the ZIF socket2.6.3 Buzzer enable/disable J9 2.6.2 CMOS clear J1Enabled Disabled2.7 Installing DRAM SODIMMs 2.8 IDE hard drive connector CN112.7.2 Installing SODIMMs 2.7.1 Introduction2.9 Floppy drive connector CN9 2.8.1 Connecting the hard drive2.10 Parallel port connector CN12 2.9.1 Connecting the floppy drive2.11 Keyboard and PS/2 mouse connector CN5 2.12 Front panel connector CN182.12.1 Speaker 2.12.2 LED interface2.13 Power connectors FAN1, CN14, CN6 2.12.4 Reset switch2.13.1 Peripheral power connector, -5 V, -12 V CN14 2.13.2 Main power connector, +5 V, +12 V CN62.14 ATX power control connector CN2, J4 2.14.1 ATX feature connector CN2 and power button J42.15 ATX power on function select J11 2.16 IR connector CN82.17 COM-port connector CN20 2.17.1 COM2 RS-232/422/485 setting J102.17.2 COM3/COM4 RI pin setting J6 PortAddress range InterruptRI default setting Table 2-8 COM1 RI pin setting J6Table 2-9 COM2 RI pin setting J6 RI default settingRI default setting Table 2-10 COM3 RI pin setting J6Table 2-11 COM4 RI pin setting J6 Chapter 2 Installation2.18.1 CRT display connector CN15 2.18.2 Flat panel display connector CN162.18.3 Ext. flat panel display connector CN17 2.18 VGA interface connections2.18.4 Panel type select SW1 Note 2 Pin 6 is reserved for PanelLink settingPanel type 2.19 Ethernet configuration 2.19.1 100Base-T connector CN12.19.2 Network boot 2.19.3 LAN controller power select J122.20 Watchdog timer configuration 2.21 USB connectors CN192.20.1 Watchdog timer action J2 2.22 SCSI connectors CN4 2.23 PanelLink CN22 optional30 PCM-9570/S Users Manual Software Configuration This chapter details the software configuration information. It showsyou how to configure the card to Sections include Introduction Ethernet interface configuration3.1 Introduction 3.2 Ethernet software configuration For Ethernet installation, please see Chapter34 PCM-9570/S Users Manual Award BIOS Setup This chapter describes how to set BIOS configuration dataC H A P T E R 4.1.1 System configuration verification 4.1 System test and initialization4.2 Award BIOS setup 4.2.1 Entering setup4.2.2 Standard CMOS setup Figure 4-2 CMOS setup screen4.2.3 BIOS features setup Figure 4-3 BIOS features setupChapter 4 Award BIOS Setup 4.2.4 Chipset features setup Figure 4-4 Chipset features setup40 PCM-9570/S Users Manual 4.2.5 Power management setup Figure 4-5 Power management setupChapter 4 Award BIOS Setup 4.2.6 PnP/PCI configuration Figure 4-6 PnP/PCI configuration42 PCM-9570/S Users Manual 4.2.7 Integrated peripherals Chapter 4 Award BIOS SetupFigure 4-7 Integrated peripherals 4.2.8 Load BIOS defaults Figure 4-8 Load BIOS defaults44 PCM-9570/S Users Manual 4.2.9 Change password Enter PasswordConfirm Password 4.2.11 Save & exit setup 4.2.10 Auto detect hard disk4.2.12 Exit without saving Figure 4-9 IDE HDD auto detection screenPCI SVGA Setup Introduction Installation of SVGA driver for Windows WindowsWindows NT C H A P T E R5.1 Introduction 5.1.1 Chipset5.1.2 Display memory 5.1.3 Display types5.1.4 Dual/simultaneous display 5.2 Installation of SVGA driver Enter means pressing the “Enter” key on thekeyboard 5.2.1 Installation for Windows 95/98 a. Select Start , Settings , Control Panel 1. Display , SettingsChapter 5 PCI SVGA Setup a. Choose the Adapter label 2. b. Press the Change... buttona. Insert the disc into the CD-ROM drive 5. b. Type D\Biscuit\9570\ c. Press OK6. select Trident Cyber 9525 DVD PCI/AGP95mV b. Click the OK button a. Click the Nexta. Click Advanced 11. for further adjustment b. Click OK to exit END Chapter 5 PCI SVGA Setupa. P re s s Ye s to 9. re b o o t The Trident5.2.2 Installation for Windows NT a. Select Start, Settings, Control Panelb. Double click the Display icon a. Choose the Settings label b. Press the Display Type button a. Press the Change... buttonIn s e rt th e d is c into th e a. Repeat Step 1 in this manual, to select the Settings label b. Adjust resolution and color 9. c. Click Test to see the resultd. Click OK to save the setting END 56 PCM-9570/S Users Manual5.3 Further information Chapter 5 PCI SVGA Setup58 PCM-9570/S Users Manual SCSI Setup and Configurations C H A P T E R6.1 Introduction If any peripheral is attached to the Ultra2 SCSIsegment and is running at SE mode, one or more Ultra/Ultra Wide peripherals will be attached to the6.3 Basic rules for SCSI host adapter and device installation 6.2 Before you beginChapter 6 SCSI Setup and Configurations 6.4 Configuring the SCSI adapter Symbios Inc. SDMS TM V 4.0 PCI SCSI BIOS PCI Rev. 2.0Copyright 1995, 1998 Symbios Inc PCI-4.12.00 Press Ctrl-C to start Symbios Configuration Utility6.5 SCSI terminators 6.6 SDMS drivers When you start the Windows NT installation witheither a CD-ROM boot or from the floppy disks, a black screen will initially appear with the following6.7 Utility users guide and installation instructions For DOSFor Windows 95/98 For Windows NT For SCO UnixFor NetWare For OS/26.8 Driver and utility installation 68 PCM-9570/S Users Manual PCI Bus Ethernet Interface This chapter provides information on Ethernet configurationIntroduction Installation of Ethernet driver for Windows 95/98/NT Further information7.2 Installation of Ethernet driver 7.2.1 Installation for MS-DOS and Windows7.1 Introduction examples only.You must follow the flow chart7.2.2 Installation for Windows 95/98 a. Select Start, Settings 1. Control Panel. b. Double click Networka. Click Add and 2. prepare to install network functions 3. add the Ethernet cardNote 1 The correct file path for Windows 98 is Biscuit\9570\Lan.100\8139b\Win9872 PCM-9570/S Users Manual 7.2.3 Installation for Windows NT a. Select Start, Settings 1. Control Panel b. Double click Networka. Choose the Adapters label 2. b. Click the Add button a. Press Have 3. Diska. Make sure the configurations of relevant items are set correctly b. Click OK to reboot E N DInsert the CD into the D\ drive7.3 Further information Chapter 7 PCI Bus Ethernet Interface76 PCM-9570/S Users Manual Programming the Watchdog Timer A P P E N D IA.1 Programming the watchdog timer Data10 REM Watchdog timer example program 80 PCM-9570/S Users Manual Installing PC/104 Modules A P P E N D IB.1 Installing PC/104 modules 82 PCM-9570/S Users ManualFigure B-1 PC/104 module mounting diagram Figure B-2 PC/104 module dimensions mm ±0.1Appendix B Installing PC/104 Modules P C /1 0 M ounting SupportSignal SignalNumber Row APin Assignments C.1 Ethernet 10/100Base-T connector CN1 C.2 ATX power feature connector CN2Signal PinSignalC.3 SCSI Connector CN4 Table C-3 SCSI connector CN4Function FunctionTable C-3 SCSI connector CN4 continued FunctionFunction 88 PCM-9570/S Users ManualC.4 Keyboard and PS/2 mouse connector CN5 SignalTable C-4 Keyboard and mouse connector CN5 Appendix C Pin AssignmentsC.5 Main power connector CN6 C.6 IR connector CN8Signal SignalC.7 Floppy drive connector CN9 SignalSignal low activeC.8 IDE hard drive connector CN11 SignalSignal 92 PCM-9570/S Users ManualC.9 Parallel port connector CN12 SignalSignal Table C-9 Parallel port connector CN12C.10 Backlight connector CN13 C.11 Peripheral power connector CN14PinSignal Table C-10 Backlight connector CN13C.12 CRT display connector CN15 SignalSignal C.13 24-bit LCD display connector CN16 Note 2 The signals shown in parentheses are for 24-bit TFT color bitsSignal SignalC.14 Ext. LCD display connector CN17 The model number of the CN16 connector isSignal SignalC.15 LCD signal mapping Table C-15 LCD signal mapping98 PCM-9570/S Users Manual C.16 Front panel connector CN18 C.17 USB connectors CN19Signal SignalC.18 COM port connector CN20 with four DSUB-9 male connectors. Theconnector are listed below for your SignalSignal RS-232RS-422 RS-485C.19 CompactFlash card connector CN21 SignalSignal 102 PCM-9570/S Users ManualC.20 PanelLink connector CN22 SignalSignal Table C-21 PanelLink connector CN22C.21 Fan power connector FAN1 PinSignalTable C-22 Fan power connector FAN1 104 PCM-9570/S Users ManualSystem Assignments A P P E N D ID.1 System I/O ports MPU-401 select from 300 ~ 330H 2 bytesAddr. range Hex DeviceD.2 1st MB memory map D.3 DMA channel assignmentsAddr. range Hex DeviceD.4 IRQ mapping chart Ethernet interface IRQ select 9, 11, 12 PnP USB IRQ select 9, 11, 12SCSI IRQ select 9, 11, 12 Optional Extras A P P E N D IE.1 PCM-10586-4 cable kit for PCM-9570/S connectorconnector 110 PCM-9570/S Users ManualE.2 USB cable E.3 SCSI cablesE.4 24-bit LCD cable adapter 112 PCM-9570/S Users Manual Mechanical Drawings A P P E N D IF.1 Component side Figure F-1 PCM-9570/S mechanical drawing - component side114 PCM-9570/S Users Manual F.2 Solder side Figure F-2 PCM-9570/S mechanical drawing - solder sideAppendix F Mechanical Drawings 116 PCM-9570/S Users Manual