Manuals / Advantech / Computer Equipment / Computer Hardware

Advantech 2006957006 5th Edition D.2 1st MB memory map, D.3 DMA channel assignments, Device

Models: 2006957006 5th Edition

1 128

Download 128 pages 42.83 Kb

Page 119

Image 119

D.2 1st MB memory map

Table D-2: 1st MB memory map

Addr. range (Hex)	Device
F000h - FFFFh	System ROM

E000h - EFFFh	Unused

D000h - DFFFh	SCSI ROM

*CC00h - CFFFh	Ethernet ROM

C000h - CBFFh	Expansion ROM

B800h - BFFFh	CGA/EGA/VGA text

B000h - B7FFh	Unused

A000h - AFFFh	EGA/VGA graphics

0000h - 9FFFh	Base memory

* If Ethernet boot ROM is enabled

D.3 DMA channel assignments

Table D-3: DMA channel assignments

Channel	Function
0	Available

1	Available

2	Floppy disk (8-bit transfer)

3	Available (Parallel Port)

4	Cascade for DMA controller 1

5	Available

6	Available

7	Available

** Parallel port DMA select 1 or 3

Appendix D System Assignments

107

Page 119

Image 119

Advantech 2006957006 5th Edition D.2 1st MB memory map, D.3 DMA channel assignments, Addr. range Hex, Device, Channel

Contents

Users Manual PCM-9570/SSocket 370 Celeron/Pentium III SBC with LCD, Ethernet and SCSI Copyright notice Acknowledgments 1 CD disc with utility and drivers 1 Startup Manual Packing listPlease refer to Appendix E for the optional interface wiring kit 1 PCM-9570/S all-in-one single board computerChapter 1 General Information ContentsChapter 2 Installation 2.10 Chapter 5 PCI SVGA Setup Chapter 3 Software ConfigurationChapter 4 Award BIOS Setup Chapter 7 PCI Bus Ethernet Interface Chapter 6 SCSI Setup and ConfigurationsTimer Appendix B Installing PC/104 ModulesE.1 PCM-10586-4 cable kit for PCM-9570/S Appendix D System AssignmentsAppendix E Optional Extras Appendix F Mechanical DrawingsTable C-19 COM2 port for RS-232, RS-422 and RS-485 CN20 TablesTable D-4 IRQ mapping chart Table C-20 CompactFlash card connector CN21Table C-21 PanelLink connector CN22 Table C-22 Fan power connector FAN1Figure F-2 PCM-9570/S mechanical drawing - solder side FiguresFigure F-1 PCM-9570/S mechanical drawing - component side This chapter gives background information on the PCM-9570/S General InformationSections include Introduction Features Specifications Board layout and dimensionsHighly integrated Socket 370 SBC 1.1 IntroductionStandard SBC functions 1.2 Features1.3 Specifications Display mode PCI SVGA/flat panel interfacePanelLink optional PCI bus Ethernet interfaceUltra2 SCSI PCM-9570S only Solid state disk6 PCM-9570/S Users Manual 1.4 Board layout and dimensionsFigure 1-1 PCM-9570/S dimensions C H A P T E R InstallationFunction 2.1 JumpersLabel Function 2.2 ConnectorsPlease refer to Appendix C for pin assignments Label10 PCM-9570/S Users Manual 2.3 Locating jumpersFigure 2-1 Locating jumpers Chapter 2 Installation 2.4 Locating connectors2.4.1 Component side Figure 2-2 Locating connectors component side12 PCM-9570/S Users Manual 2.4.2 Solder sideFigure 2-3 Locating connectors solder side 2.5 Setting jumpers 2.6.1 Installing a CPU in the ZIF socket 2.6 CPU installation and upgradingDisabled 2.6.3 Buzzer enable/disable J92.6.2 CMOS clear J1 Enabled2.7.1 Introduction 2.7 Installing DRAM SODIMMs2.8 IDE hard drive connector CN11 2.7.2 Installing SODIMMs2.8.1 Connecting the hard drive 2.9 Floppy drive connector CN92.9.1 Connecting the floppy drive 2.10 Parallel port connector CN122.12.2 LED interface 2.11 Keyboard and PS/2 mouse connector CN52.12 Front panel connector CN18 2.12.1 Speaker2.13.2 Main power connector, +5 V, +12 V CN6 2.13 Power connectors FAN1, CN14, CN62.12.4 Reset switch 2.13.1 Peripheral power connector, -5 V, -12 V CN142.14.1 ATX feature connector CN2 and power button J4 2.14 ATX power control connector CN2, J42.17.1 COM2 RS-232/422/485 setting J10 2.15 ATX power on function select J112.16 IR connector CN8 2.17 COM-port connector CN20Interrupt 2.17.2 COM3/COM4 RI pin setting J6Port Address rangeRI default setting RI default settingTable 2-8 COM1 RI pin setting J6 Table 2-9 COM2 RI pin setting J6Chapter 2 Installation RI default settingTable 2-10 COM3 RI pin setting J6 Table 2-11 COM4 RI pin setting J62.18 VGA interface connections 2.18.1 CRT display connector CN152.18.2 Flat panel display connector CN16 2.18.3 Ext. flat panel display connector CN17Panel type 2.18.4 Panel type select SW1Note 2 Pin 6 is reserved for PanelLink setting 2.19.3 LAN controller power select J12 2.19 Ethernet configuration2.19.1 100Base-T connector CN1 2.19.2 Network boot2.20.1 Watchdog timer action J2 2.20 Watchdog timer configuration2.21 USB connectors CN19 30 PCM-9570/S Users Manual 2.22 SCSI connectors CN42.23 PanelLink CN22 optional Sections include Introduction Ethernet interface configuration Software ConfigurationThis chapter details the software configuration information. It shows you how to configure the card to3.1 Introduction For Ethernet installation, please see Chapter 3.2 Ethernet software configuration34 PCM-9570/S Users Manual C H A P T E R Award BIOS SetupThis chapter describes how to set BIOS configuration data 4.1 System test and initialization 4.1.1 System configuration verification4.2.1 Entering setup 4.2 Award BIOS setupFigure 4-2 CMOS setup screen 4.2.2 Standard CMOS setupChapter 4 Award BIOS Setup 4.2.3 BIOS features setupFigure 4-3 BIOS features setup 40 PCM-9570/S Users Manual 4.2.4 Chipset features setupFigure 4-4 Chipset features setup Chapter 4 Award BIOS Setup 4.2.5 Power management setupFigure 4-5 Power management setup 42 PCM-9570/S Users Manual 4.2.6 PnP/PCI configurationFigure 4-6 PnP/PCI configuration Figure 4-7 Integrated peripherals 4.2.7 Integrated peripheralsChapter 4 Award BIOS Setup 44 PCM-9570/S Users Manual 4.2.8 Load BIOS defaultsFigure 4-8 Load BIOS defaults Confirm Password 4.2.9 Change passwordEnter Password Figure 4-9 IDE HDD auto detection screen 4.2.11 Save & exit setup4.2.10 Auto detect hard disk 4.2.12 Exit without savingC H A P T E R PCI SVGA SetupIntroduction Installation of SVGA driver for Windows Windows Windows NT5.1.3 Display types 5.1 Introduction5.1.1 Chipset 5.1.2 Display memory5.1.4 Dual/simultaneous display keyboard 5.2 Installation of SVGA driverEnter means pressing the “Enter” key on the a. Choose the Adapter label 2. b. Press the Change... button 5.2.1 Installation for Windows 95/98a. Select Start , Settings , Control Panel 1. Display , Settings Chapter 5 PCI SVGA Setupa. Click the Next a. Insert the disc into the CD-ROM drive 5. b. Type D\Biscuit\9570\c. Press OK 6. select Trident Cyber 9525 DVD PCI/AGP95mV b. Click the OK buttonThe Trident a. Click Advanced 11. for further adjustment b. Click OK to exit ENDChapter 5 PCI SVGA Setup a. P re s s Ye s to 9. re b o o tb. Press the Display Type button a. Press the Change... button 5.2.2 Installation for Windows NTa. Select Start, Settings, Control Panel b. Double click the Display icon a. Choose the Settings labelIn s e rt th e d is c into th e 56 PCM-9570/S Users Manual a. Repeat Step 1 in this manual, to select the Settings labelb. Adjust resolution and color 9. c. Click Test to see the result d. Click OK to save the setting ENDChapter 5 PCI SVGA Setup 5.3 Further information58 PCM-9570/S Users Manual C H A P T E R SCSI Setup and ConfigurationsUltra/Ultra Wide peripherals will be attached to the 6.1 IntroductionIf any peripheral is attached to the Ultra2 SCSI segment and is running at SE mode, one or moreChapter 6 SCSI Setup and Configurations 6.3 Basic rules for SCSI host adapter and device installation6.2 Before you begin Press Ctrl-C to start Symbios Configuration Utility 6.4 Configuring the SCSI adapterSymbios Inc. SDMS TM V 4.0 PCI SCSI BIOS PCI Rev. 2.0 Copyright 1995, 1998 Symbios Inc PCI-4.12.006.5 SCSI terminators black screen will initially appear with the following 6.6 SDMS driversWhen you start the Windows NT installation with either a CD-ROM boot or from the floppy disks, aFor Windows 95/98 6.7 Utility users guide and installation instructionsFor DOS For OS/2 For Windows NTFor SCO Unix For NetWare6.8 Driver and utility installation 68 PCM-9570/S Users Manual Further information PCI Bus Ethernet InterfaceThis chapter provides information on Ethernet configuration Introduction Installation of Ethernet driver for Windows 95/98/NTexamples only.You must follow the flow chart 7.2 Installation of Ethernet driver7.2.1 Installation for MS-DOS and Windows 7.1 Introduction3. add the Ethernet card 7.2.2 Installation for Windows 95/98a. Select Start, Settings 1. Control Panel. b. Double click Network a. Click Add and 2. prepare to install network functions72 PCM-9570/S Users Manual Note 1 The correct file path for Windows 98 isBiscuit\9570\Lan.100\8139b\Win98 3. Disk 7.2.3 Installation for Windows NTa. Select Start, Settings 1. Control Panel b. Double click Network a. Choose the Adapters label 2. b. Click the Add button a. Press Haveinto the D\ drive a. Make sure the configurations of relevant items are set correctlyb. Click OK to reboot E N D Insert the CDChapter 7 PCI Bus Ethernet Interface 7.3 Further information76 PCM-9570/S Users Manual A P P E N D I Programming the Watchdog TimerData A.1 Programming the watchdog timer10 REM Watchdog timer example program 80 PCM-9570/S Users Manual A P P E N D I Installing PC/104 Modules82 PCM-9570/S Users Manual B.1 Installing PC/104 modulesP C /1 0 M ounting Support Figure B-1 PC/104 module mounting diagramFigure B-2 PC/104 module dimensions mm ±0.1 Appendix B Installing PC/104 ModulesRow A SignalSignal NumberPin Assignments PinSignal C.1 Ethernet 10/100Base-T connector CN1C.2 ATX power feature connector CN2 SignalFunction C.3 SCSI Connector CN4Table C-3 SCSI connector CN4 Function88 PCM-9570/S Users Manual Table C-3 SCSI connector CN4 continuedFunction FunctionAppendix C Pin Assignments C.4 Keyboard and PS/2 mouse connector CN5Signal Table C-4 Keyboard and mouse connector CN5Signal C.5 Main power connector CN6C.6 IR connector CN8 Signallow active C.7 Floppy drive connector CN9Signal Signal92 PCM-9570/S Users Manual C.8 IDE hard drive connector CN11Signal SignalTable C-9 Parallel port connector CN12 C.9 Parallel port connector CN12Signal SignalTable C-10 Backlight connector CN13 C.10 Backlight connector CN13C.11 Peripheral power connector CN14 PinSignalSignal C.12 CRT display connector CN15Signal Signal C.13 24-bit LCD display connector CN16Note 2 The signals shown in parentheses are for 24-bit TFT color bits SignalSignal C.14 Ext. LCD display connector CN17The model number of the CN16 connector is Signal98 PCM-9570/S Users Manual C.15 LCD signal mappingTable C-15 LCD signal mapping Signal C.16 Front panel connector CN18C.17 USB connectors CN19 SignalSignal C.18 COM port connector CN20with four DSUB-9 male connectors. The connector are listed below for yourRS-485 SignalRS-232 RS-422102 PCM-9570/S Users Manual C.19 CompactFlash card connector CN21Signal SignalTable C-21 PanelLink connector CN22 C.20 PanelLink connector CN22Signal Signal104 PCM-9570/S Users Manual C.21 Fan power connector FAN1PinSignal Table C-22 Fan power connector FAN1A P P E N D I System AssignmentsDevice D.1 System I/O portsMPU-401 select from 300 ~ 330H 2 bytes Addr. range HexDevice D.2 1st MB memory mapD.3 DMA channel assignments Addr. range HexSCSI IRQ select 9, 11, 12 D.4 IRQ mapping chartEthernet interface IRQ select 9, 11, 12 PnP USB IRQ select 9, 11, 12 A P P E N D I Optional Extras110 PCM-9570/S Users Manual E.1 PCM-10586-4 cable kit for PCM-9570/Sconnector connectorE.4 24-bit LCD cable adapter E.2 USB cableE.3 SCSI cables 112 PCM-9570/S Users Manual A P P E N D I Mechanical Drawings114 PCM-9570/S Users Manual F.1 Component sideFigure F-1 PCM-9570/S mechanical drawing - component side Appendix F Mechanical Drawings F.2 Solder sideFigure F-2 PCM-9570/S mechanical drawing - solder side 116 PCM-9570/S Users Manual

D.2 1st MB memory map

D.3 DMA channel assignments

Channel