Manuals / Advantech / Computer Equipment / Computer Hardware

Advantech 2006957006 5th Edition user manual C.20 PanelLink connector CN22, Signal

Models: 2006957006 5th Edition

1 128

Download 128 pages 42.83 Kb

Page 115

Image 115

C.20 PanelLink connector (CN22)

Table C-21: PanelLink connector (CN22)

Pin	Signal	Pin	Signal
1	TX1+	2	TX1-

3	TX1 GND	4	TXC GND

5	TXC+	6	TXC-

7	DDC GND	8	VDD 5 V

9	VDD 5 V	10	VDD 5 V

11	TX2+	12	TX2-

13	TX2 GND	14	TX0 GND

15	TX0+	16	TX0-

17	NC	18	NC

19	DDC/SDA (reserved)	20	DDC/SCL (reserved)

Appendix C Pin Assignments

103

Page 115

Image 115

Advantech 2006957006 5th Edition user manual C.20 PanelLink connector CN22, Signal, Table C-21 PanelLink connector CN22

Contents

Socket 370 Celeron/Pentium III SBC with LCD, Ethernet and SCSI PCM-9570/SUsers Manual Copyright notice Acknowledgments 1 CD disc with utility and drivers 1 Startup Manual Packing listPlease refer to Appendix E for the optional interface wiring kit 1 PCM-9570/S all-in-one single board computerChapter 2 Installation ContentsChapter 1 General Information 2.10 Chapter 4 Award BIOS Setup Chapter 3 Software ConfigurationChapter 5 PCI SVGA Setup Chapter 7 PCI Bus Ethernet Interface Chapter 6 SCSI Setup and ConfigurationsTimer Appendix B Installing PC/104 ModulesE.1 PCM-10586-4 cable kit for PCM-9570/S Appendix D System AssignmentsAppendix E Optional Extras Appendix F Mechanical DrawingsTable C-19 COM2 port for RS-232, RS-422 and RS-485 CN20 TablesTable D-4 IRQ mapping chart Table C-20 CompactFlash card connector CN21Table C-21 PanelLink connector CN22 Table C-22 Fan power connector FAN1Figure F-1 PCM-9570/S mechanical drawing - component side FiguresFigure F-2 PCM-9570/S mechanical drawing - solder side This chapter gives background information on the PCM-9570/S General InformationSections include Introduction Features Specifications Board layout and dimensionsHighly integrated Socket 370 SBC 1.1 Introduction1.3 Specifications 1.2 FeaturesStandard SBC functions Display mode PCI SVGA/flat panel interfacePanelLink optional PCI bus Ethernet interfaceUltra2 SCSI PCM-9570S only Solid state diskFigure 1-1 PCM-9570/S dimensions 1.4 Board layout and dimensions6 PCM-9570/S Users Manual C H A P T E R InstallationLabel 2.1 JumpersFunction Function 2.2 ConnectorsPlease refer to Appendix C for pin assignments LabelFigure 2-1 Locating jumpers 2.3 Locating jumpers10 PCM-9570/S Users Manual Chapter 2 Installation 2.4 Locating connectors2.4.1 Component side Figure 2-2 Locating connectors component sideFigure 2-3 Locating connectors solder side 2.4.2 Solder side12 PCM-9570/S Users Manual 2.5 Setting jumpers 2.6.1 Installing a CPU in the ZIF socket 2.6 CPU installation and upgradingDisabled 2.6.3 Buzzer enable/disable J92.6.2 CMOS clear J1 Enabled2.7.1 Introduction 2.7 Installing DRAM SODIMMs2.8 IDE hard drive connector CN11 2.7.2 Installing SODIMMs2.8.1 Connecting the hard drive 2.9 Floppy drive connector CN92.9.1 Connecting the floppy drive 2.10 Parallel port connector CN122.12.2 LED interface 2.11 Keyboard and PS/2 mouse connector CN52.12 Front panel connector CN18 2.12.1 Speaker2.13.2 Main power connector, +5 V, +12 V CN6 2.13 Power connectors FAN1, CN14, CN62.12.4 Reset switch 2.13.1 Peripheral power connector, -5 V, -12 V CN142.14.1 ATX feature connector CN2 and power button J4 2.14 ATX power control connector CN2, J42.17.1 COM2 RS-232/422/485 setting J10 2.15 ATX power on function select J112.16 IR connector CN8 2.17 COM-port connector CN20Interrupt 2.17.2 COM3/COM4 RI pin setting J6Port Address rangeRI default setting RI default settingTable 2-8 COM1 RI pin setting J6 Table 2-9 COM2 RI pin setting J6Chapter 2 Installation RI default settingTable 2-10 COM3 RI pin setting J6 Table 2-11 COM4 RI pin setting J62.18 VGA interface connections 2.18.1 CRT display connector CN152.18.2 Flat panel display connector CN16 2.18.3 Ext. flat panel display connector CN17Note 2 Pin 6 is reserved for PanelLink setting 2.18.4 Panel type select SW1Panel type 2.19.3 LAN controller power select J12 2.19 Ethernet configuration2.19.1 100Base-T connector CN1 2.19.2 Network boot2.21 USB connectors CN19 2.20 Watchdog timer configuration2.20.1 Watchdog timer action J2 2.23 PanelLink CN22 optional 2.22 SCSI connectors CN430 PCM-9570/S Users Manual Sections include Introduction Ethernet interface configuration Software ConfigurationThis chapter details the software configuration information. It shows you how to configure the card to3.1 Introduction For Ethernet installation, please see Chapter 3.2 Ethernet software configuration34 PCM-9570/S Users Manual This chapter describes how to set BIOS configuration data Award BIOS SetupC H A P T E R 4.1 System test and initialization 4.1.1 System configuration verification4.2.1 Entering setup 4.2 Award BIOS setupFigure 4-2 CMOS setup screen 4.2.2 Standard CMOS setupFigure 4-3 BIOS features setup 4.2.3 BIOS features setupChapter 4 Award BIOS Setup Figure 4-4 Chipset features setup 4.2.4 Chipset features setup40 PCM-9570/S Users Manual Figure 4-5 Power management setup 4.2.5 Power management setupChapter 4 Award BIOS Setup Figure 4-6 PnP/PCI configuration 4.2.6 PnP/PCI configuration42 PCM-9570/S Users Manual Chapter 4 Award BIOS Setup 4.2.7 Integrated peripheralsFigure 4-7 Integrated peripherals Figure 4-8 Load BIOS defaults 4.2.8 Load BIOS defaults44 PCM-9570/S Users Manual Enter Password 4.2.9 Change passwordConfirm Password Figure 4-9 IDE HDD auto detection screen 4.2.11 Save & exit setup4.2.10 Auto detect hard disk 4.2.12 Exit without savingC H A P T E R PCI SVGA SetupIntroduction Installation of SVGA driver for Windows Windows Windows NT5.1.3 Display types 5.1 Introduction5.1.1 Chipset 5.1.2 Display memory5.1.4 Dual/simultaneous display Enter means pressing the “Enter” key on the 5.2 Installation of SVGA driverkeyboard a. Choose the Adapter label 2. b. Press the Change... button 5.2.1 Installation for Windows 95/98a. Select Start , Settings , Control Panel 1. Display , Settings Chapter 5 PCI SVGA Setupa. Click the Next a. Insert the disc into the CD-ROM drive 5. b. Type D\Biscuit\9570\c. Press OK 6. select Trident Cyber 9525 DVD PCI/AGP95mV b. Click the OK buttonThe Trident a. Click Advanced 11. for further adjustment b. Click OK to exit ENDChapter 5 PCI SVGA Setup a. P re s s Ye s to 9. re b o o tb. Press the Display Type button a. Press the Change... button 5.2.2 Installation for Windows NTa. Select Start, Settings, Control Panel b. Double click the Display icon a. Choose the Settings labelIn s e rt th e d is c into th e 56 PCM-9570/S Users Manual a. Repeat Step 1 in this manual, to select the Settings labelb. Adjust resolution and color 9. c. Click Test to see the result d. Click OK to save the setting ENDChapter 5 PCI SVGA Setup 5.3 Further information58 PCM-9570/S Users Manual C H A P T E R SCSI Setup and ConfigurationsUltra/Ultra Wide peripherals will be attached to the 6.1 IntroductionIf any peripheral is attached to the Ultra2 SCSI segment and is running at SE mode, one or more6.2 Before you begin 6.3 Basic rules for SCSI host adapter and device installationChapter 6 SCSI Setup and Configurations Press Ctrl-C to start Symbios Configuration Utility 6.4 Configuring the SCSI adapterSymbios Inc. SDMS TM V 4.0 PCI SCSI BIOS PCI Rev. 2.0 Copyright 1995, 1998 Symbios Inc PCI-4.12.006.5 SCSI terminators black screen will initially appear with the following 6.6 SDMS driversWhen you start the Windows NT installation with either a CD-ROM boot or from the floppy disks, aFor DOS 6.7 Utility users guide and installation instructionsFor Windows 95/98 For OS/2 For Windows NTFor SCO Unix For NetWare6.8 Driver and utility installation 68 PCM-9570/S Users Manual Further information PCI Bus Ethernet InterfaceThis chapter provides information on Ethernet configuration Introduction Installation of Ethernet driver for Windows 95/98/NTexamples only.You must follow the flow chart 7.2 Installation of Ethernet driver7.2.1 Installation for MS-DOS and Windows 7.1 Introduction3. add the Ethernet card 7.2.2 Installation for Windows 95/98a. Select Start, Settings 1. Control Panel. b. Double click Network a. Click Add and 2. prepare to install network functionsBiscuit\9570\Lan.100\8139b\Win98 Note 1 The correct file path for Windows 98 is72 PCM-9570/S Users Manual 3. Disk 7.2.3 Installation for Windows NTa. Select Start, Settings 1. Control Panel b. Double click Network a. Choose the Adapters label 2. b. Click the Add button a. Press Haveinto the D\ drive a. Make sure the configurations of relevant items are set correctlyb. Click OK to reboot E N D Insert the CDChapter 7 PCI Bus Ethernet Interface 7.3 Further information76 PCM-9570/S Users Manual A P P E N D I Programming the Watchdog TimerData A.1 Programming the watchdog timer10 REM Watchdog timer example program 80 PCM-9570/S Users Manual A P P E N D I Installing PC/104 Modules82 PCM-9570/S Users Manual B.1 Installing PC/104 modulesP C /1 0 M ounting Support Figure B-1 PC/104 module mounting diagramFigure B-2 PC/104 module dimensions mm ±0.1 Appendix B Installing PC/104 ModulesRow A SignalSignal NumberPin Assignments PinSignal C.1 Ethernet 10/100Base-T connector CN1C.2 ATX power feature connector CN2 SignalFunction C.3 SCSI Connector CN4Table C-3 SCSI connector CN4 Function88 PCM-9570/S Users Manual Table C-3 SCSI connector CN4 continuedFunction FunctionAppendix C Pin Assignments C.4 Keyboard and PS/2 mouse connector CN5Signal Table C-4 Keyboard and mouse connector CN5Signal C.5 Main power connector CN6C.6 IR connector CN8 Signallow active C.7 Floppy drive connector CN9Signal Signal92 PCM-9570/S Users Manual C.8 IDE hard drive connector CN11Signal SignalTable C-9 Parallel port connector CN12 C.9 Parallel port connector CN12Signal SignalTable C-10 Backlight connector CN13 C.10 Backlight connector CN13C.11 Peripheral power connector CN14 PinSignalSignal C.12 CRT display connector CN15Signal Signal C.13 24-bit LCD display connector CN16Note 2 The signals shown in parentheses are for 24-bit TFT color bits SignalSignal C.14 Ext. LCD display connector CN17The model number of the CN16 connector is SignalTable C-15 LCD signal mapping C.15 LCD signal mapping98 PCM-9570/S Users Manual Signal C.16 Front panel connector CN18C.17 USB connectors CN19 SignalSignal C.18 COM port connector CN20with four DSUB-9 male connectors. The connector are listed below for yourRS-485 SignalRS-232 RS-422102 PCM-9570/S Users Manual C.19 CompactFlash card connector CN21Signal SignalTable C-21 PanelLink connector CN22 C.20 PanelLink connector CN22Signal Signal104 PCM-9570/S Users Manual C.21 Fan power connector FAN1PinSignal Table C-22 Fan power connector FAN1A P P E N D I System AssignmentsDevice D.1 System I/O portsMPU-401 select from 300 ~ 330H 2 bytes Addr. range HexDevice D.2 1st MB memory mapD.3 DMA channel assignments Addr. range HexEthernet interface IRQ select 9, 11, 12 PnP USB IRQ select 9, 11, 12 D.4 IRQ mapping chartSCSI IRQ select 9, 11, 12 A P P E N D I Optional Extras110 PCM-9570/S Users Manual E.1 PCM-10586-4 cable kit for PCM-9570/Sconnector connectorE.3 SCSI cables E.2 USB cableE.4 24-bit LCD cable adapter 112 PCM-9570/S Users Manual A P P E N D I Mechanical DrawingsFigure F-1 PCM-9570/S mechanical drawing - component side F.1 Component side114 PCM-9570/S Users Manual Figure F-2 PCM-9570/S mechanical drawing - solder side F.2 Solder sideAppendix F Mechanical Drawings 116 PCM-9570/S Users Manual