Configuring the Scsi adapter | Advantech 2006957006 5th Edition

6.4 Configuring the SCSI adapter

Access the SCSI BIOS by holding down both the CTRL and C keys when you see the BIOS banner message listing the driver name and the attached devices. For example:

Symbios Inc. SDMS (TM) V 4.0 PCI SCSI BIOS PCI Rev. 2.0, 2.1

Copyright 1995, 1998 Symbios Inc.

PCI-4.12.00

Press Ctrl-C to start Symbios Configuration

Utility...

The SCSI Select screen will come up. Instructions on how to move the cursor and select options are listed on the bottom of the program windows. You can select either Configure/View Host Adapter Settings or SCSI CD Utilities.

62 PCM-9570/S User's Manual

Image 74

Advantech 2006957006 5th Edition user manual Configuring the Scsi adapter

Contents

PCM-9570/S Copyright notice Acknowledgments Packing list Contents ATX feature connector CN2 and power button PCI Svga Setup Software ConfigurationAward Bios Setup PCI Bus Ethernet Interface Scsi Setup and ConfigurationsAppendix a Programming the Watchdog Timer Appendix C Pin Assignments Appendix F Mechanical Drawings Appendix D System AssignmentsAppendix E Optional Extras Tables Table C-20 CompactFlash card connector CN21 102 Figures General Information Introduction Highly integrated Socket 370 SBC Features Display mode PCI SVGA/flat panel interface Solid state disk PCI bus Ethernet interfaceUltra2 Scsi PCM-9570S only PanelLink optional Board layout and dimensions PCM-9570/S dimensions Installation Jumpers Label Function Connectors CN9 Locating jumpers Locating jumpers Locating connectors Component side Locating connectors solder side Solder side Setting jumpers CPU installation and upgrading Installing a CPU in the ZIF socket Buzzer enable/disable J9 Cmos clear J1 Installing SODIMMs Installing Dram SODIMMsIDE hard drive connector CN11 Introduction Floppy drive connector CN9 Connecting the hard drive Parallel port connector CN12 Connecting the floppy drive Speaker Keyboard and PS/2 mouse connector CN5Front panel connector CN18 LED interface Peripheral power connector, -5 V, -12 V CN14 Power connectors FAN1, CN14, CN6Reset switch Main power connector, +5 V, +12 V CN6 ATX power control connector CN2, J4 ATX power on function select J11 17.2 COM3/COM4 RI pin setting J6 +12 RI default setting +12 18.3 Ext. flat panel display connector CN17 CRT display connector CN15Flat panel display connector CN16 VGA interface connections Panel type select SW1 Panel type Pin Network boot Ethernet configuration19.1 100Base-T connector CN1 LAN controller power select J12 Watchdog timer action J2 Watchdog timer configurationUSB connectors CN19 Scsi connectors CN4 PanelLink CN22 optional Software Configuration Introduction Ethernet software configuration Page Award Bios Setup System configuration verification System test and initialization Entering setup Setup program initial screen Standard Cmos setup Cmos setup screen Bios features setup Bios features setup Chipset features setup Chipset features setup Power management setup Power management setup 6 PnP/PCI configuration PnP/PCI configuration Integrated peripherals Integrated peripherals Load Bios defaults Load Bios defaults Change password Enter Password Exit without saving Save & exit setupAuto detect hard disk PCI Svga Setup Display types ChipsetDisplay memory Selecting display settings Dual/simultaneous display Installation of Svga driver Installation for Windows 95/98 Insert the disc into the CD-ROM drive Type \Biscuit\9570\ END Installation for Windows NT \Biscuit\9570\VGA.100\Winnt END Further information Page Scsi Setup Configurations If any peripheral is attached to the Ultra2 Scsi Basic rules for Scsi host adapter and device installation Before you begin Configuring the Scsi adapter Scsi terminators Sdms drivers Text at the top Utility users guide and installation instructions For DOS For OS/2 Driver and utility installation Other tools and utilitiesPage PCI Bus Ethernet Interface Installation of Ethernet driver Installation for MS-DOS and Windows PCI Bus Ethernet Interface Biscuit\9570\Lan.100\8139b\Win98 Press OK Scuit\9570\Lan.100\8139b\Winnt\ Further information Page Programming the Watchdog Timer Programming the watchdog timer Gosub 2000 REM Your application task #2 Page Installing PC/104 Modules Installing PC/104 modules Figure B-1 PC/104 module mounting diagram Active low Pin Assignments Ethernet 10/100Base-T connector CN1 ATX power feature connector CN2 Scsi Connector CN4 Pin Function ATN+ GND BSY+ ACK+ RST+ MSG+ SEL+ CD+ REQ+ IO+ MS VCC Main power connector CN6 IR connector CN8 Low active Table C-8 IDE hard drive connector CN11 Strobe Autofd ERR Init Slctini GND ACK Busy Backlight connector CN13 Peripheral power connector CN14 CRT display connector CN15 13 24-bit LCD display connector CN16 14 Ext. LCD display connector CN17 LCD signal mapping Table C-15 LCD signal mapping HDD LED+ V CC COM port connector CN20 Reference Pin Signal RS-232 RS-422 RS-485 CompactFlash card connector CN21 PanelLink connector CN22 Fan power connector FAN1 System Assignments System I/O ports Addr. range Hex Device 1st MB memory map DMA channel assignments IRQ mapping chart Optional Extras PCM-10586-4 cable kit for PCM-9570/S 24-bit LCD cable adapter USB cableScsi cables Page Mechanical Drawings Component side Figure F-1 PCM-9570/S mechanical drawing component side Solder side Figure F-2 PCM-9570/S mechanical drawing solder side