IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using the Andis Clipper.

DANGER: To reduce the risk of electric shock:

1.Do not reach for an appliance that has fallen into water. Unplug immediately.

2.Do not use while bathing or in a shower.

3.Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.

4.Always unplug this appliance from the electrical outlet immediately after using.

5.Unplug this appliance before cleaning, removing, or assembling parts.

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:

1.

An appliance should never be left unattended when plugged in.

2.

Close supervision is necessary when this appliance is used by, on or near

 

children or individuals with certain disabilities.

3.

Use this appliance only for its intended use as described in this manual.

 

Do not use attachments not recommended by Andis.

4.

Never operate this appliance if it has a damaged cord or plug, if it is not

 

working properly, if it has been dropped or damaged, or dropped into water.

 

Return the appliance to an Andis Service Center for examination or repair.

5.

Keep the cord away from heated surfaces.

6.

Never drop or insert any object into any opening.

7.

Do not use outdoors or operate where aerosol (spray) products are being

 

used or where oxygen is being administered.

USER MAINTENANCE

The internal mechanism of your clipper has been permanently lubricated at the factory. Other than the recommended maintenance described in this manual, no other maintenance should be performed, except by Andis Company or an Andis Authorized Repair Service Station.

CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES

Blades should be oiled before, during, and after each use. If your clipper blades leave streaks or slow down, it’s a sure sign blades need oil. The clipper should be held in the position shown in Diagram B to prevent oil from getting into the motor. Place a few drops of Andis Clipper Oil on the front and side of the cutter blades (Diagram A). Wipe excess oil off blades with a soft dry cloth. Spray lubricants contain insufficient oil for good lubrication. Always replace broken or nicked blades to prevent injury. You can clean the excess hair from your blades by using a small brush or worn out toothbrush.

To clean the blades we suggest to immerse the blades only into a shallow pan of Andis Clipper Oil, while the clipper is running. Any excess hair and dirt that has accumulated between the blades should come out. After cleaning, turn your clipper off and dry blades with a dry cloth and start clipping again.

OIL

OIL

OIL

DIAGRAM A

DIAGRAM B

FACTORY REPAIR SERVICE

When the blades of your Andis Clipper become dull after repeated use, it is advised to purchase a new set of blades available through your Andis Supplier or through an Andis Authorized Repair Station.

If you wish your clipper to be serviced as well, it should be carefully packed and mailed either Parcel Post Insured, or U.P.S. to any Andis Authorized Repair Service Station.

ATTACHING THE CLIPPER COMBS

The clipper comb blade attachments mount easily. Just snap them on. Snap them off. You can always set the blades for a coarser cut by attaching any of the snap-on blade attachments made for your Andis Clipper. To use blade attachment, slip the cutter blade teeth into blade attachment. Snap the blade attachment down; they snap on and off easily. These attachments guide hair into the clipper blades and give you precise control of hair lengths. The length of trim is indicated on the blade attachment: 1/16", 1/8", 1/4", 3/8", 1/2", 5/8", 3/4", 7/8" & 1". Use the chart below to find the approximate lengths of cut. Different blade angles in relation to the skin, thickness and texture of the hair will vary the cutting length.

CLIPPING GUIDE

 

 

Approximate Length of Cut

Description

Clipping Direction

Fine

 

Coarse

 

 

 

 

 

Standard Andis Blade

With hair grain

1/16"

to

3/16"

 

Against hair grain

1/32"

to

1/8"

 

 

 

 

 

1/16" Blade Attachment

With hair grain

3/16"

to

5/16"

 

Against hair grain

3/32"

to

5/32"

S P A N I S H

PRECAUCIONES IMPORTANTES

Al utilizar un artefacto eléctrico, siempre deben seguirse las precauciones básicas de seguridad, que incluyen las siguientes: Lea todas las instrucciones antes de usar la recortadora Andis.

PELIGRO: Para reducir el riesgo de descarga eléctrica:

1.Si un artefacto se ha caído al agua, no trate de sacarlo. Desenchúfelo inmediatamente.

2.No lo utilice al bañarse o ducharse.

3.No coloque ni almacene el artefacto donde pueda caerse en una bañera o un lavabo, o ser halado dentro de éstos. No lo coloque ni lo deje caer en agua u otro líquido.

4.Siempre desenchufe este artefacto del tomacorriente eléctrico inmediatamente después de usarlo.

5.Desenchufe este artefacto antes de limpiar, desmontar o ensamblar las piezas.

ADVERTENCIA: Para reducir el riesgo de quemaduras, incendio, descarga eléctrica o lesiones a las personas:

1.

Un artefacto nunca debe dejarse desatendido mientras está enchufado.

2.

Es necesaria una supervisión muy de cerca cuando este artefacto sea usado

 

por, en o cerca de niños o personas con ciertas discapacidades.

3.

Utilice este artefacto exclusivamente para su uso propuesto, tal como se

 

describe en este manual. No utilice accesorios no recomendados por Andis.

4.

Nunca opere este artefacto si su cable eléctrico o enchufe está dañado, si no

 

está funcionando correctamente o si se ha dejado caer, si se ha dañado o si se

INSTRUCCIONES DE OPERACIÓN

Sírvase leer las instrucciones siguientes antes de usar su nueva recortadora Andis. Al brindar el cuidado que se merece un instrumento fino construido con precisión, obtendrá muchos años de servicio. Antes de encender la recortadora, quite el protector de la hoja. Enchufe en el tomacorriente eléctrico, opere a una corriente eléctrica de CA de 120 voltios y 60 ciclos, o según se indique en la unidad. Para arrancar la recortadora, mueva el botón interruptor a la posición de encendido; para detenerla, vuelva a poner el botón interruptor en la posición original. Después de usar su recortadora Andis, vuelva a enrollar el cable y almacénela en un lugar seguro.

MANTENIMIENTO POR PARTE DEL USUARIO

El mecanismo interno de su recortadora ha sido lubricado de manera permanente en la fábrica. No debe realizarse ningún tipo de mantenimiento que no sea el mantenimiento recomendado en este manual, salvo por Andis Company o por una Estación de Servicio de Reparación Autorizada de Andis.

CUIDADO Y MANTENIMIENTO DE LAS HOJAS DE SU RECORTADORA ANDIS

Las hojas deben engrasarse antes, durante y después de cada uso. Si las hojas de su recortadora dejan manchas o si reducen su velocidad, es un indicio certero de que las mismas necesitan aceite. La recortadora debe sujetarse en la posición mostrada en el Diagrama B para evitar que el aceite penetre en el motor. Coloque unas pocas gotas de Aceite Andis para recortadoras en las partes frontal y lateral de las hojas cortadoras (Diagrama A). Limpie el exceso de aceite de las hojas usando un paño suave seco. Los lubricantes en aerosol contienen una cantidad insuficiente de aceite para lograr una buena lubricación. Siempre reemplace las hojas rotas o melladas para evitar lesiones. Puede limpiar el exceso de cabello de sus hojas usando un cepillo pequeño o un cepillo de dientes gastado. Para limpiar las hojas, sugerimos sumergir sólo las hojas en una bandeja poco profunda con Aceite Andis, mientras la recortadora esté en funcionamiento. Debiera eliminarse así todo exceso de cabello o suciedad que se hubiera acumulado entre las hojas. Después de limpiar, apague la recortadora y seque las hojas con un paño seco y comience a recortar una vez más.

LUBRICAR

LUBRICAR

LUBRICAR

 

LEVA

RESORTE DE TENSIÓN

 

 

HOJA

 

 

SUPERIOR

 

 

HOJA

 

 

INFERIOR

YUGO

ORIFICIOS PARA LOS

 

TORNILLOS DE LA HOJA

 

 

DIAGRAMA D

CONEXIÓN DE LOS PEINES DE LA RECORTADORA

Los peines accesorios para las hojas de la recortadora son fáciles de montar. Simplemente debe engancharlos. Y luego desengancharlos. Siempre puede fijar las hojas para lograr un corte más grueso conectando cualquiera de los accesorios enganchables para las hojas fabricados para su Recortadora Andis. Para usar el accesorio para las hojas, deslice los dientes de las hojas de la recortadora en el interior del accesorio. El largo de corte es indicado en los accesorios de cuchilla: 1/16" (1.6 mm), 1/8" (3 mm), 1/4" (5 mm), 3/8" (9.5 mm), 1/2" (13 mm), 5/8" (16 mm), 3/4" (19 mm), 7/8" (22 mm) y 1" (25.4 mm). Use la guía de corte para determinar la longitud de corte aproximada. Los diferentes ángulos de la cuchilla en relación con la piel, el grosor y la textura del pelo afectan el largo de corte.

8.

Do not use this appliance with a damaged or broken blade or comb, as injury

 

to the skin may occur.

9.

To disconnect turn control to “off” then remove plug from outlet.

SAVE THESE INSTRUCTIONS

This appliance is intended for COMMERCIAL use

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,

REPLACEMENT (REMOVAL) OF BLADE SET

To remove the blades, first unplug the clipper from the electrical outlet. Turn the clipper upside down, so that the blade teeth are pointing down. You may want to place the clipper on a flat surface to do this. Unscrew the screws on the blade (Diagram C). Remove the blade.

To replace the blade, put the blade back into position while aligning the yoke of the upper blade with the cam and tension spring of the clipper (Diagram D). Line up the screw holes in the bottom blade with the two holes in the blade bracket, and replace screws. Do not over tighten screws.

BLADE SCREWS

DIAGRAM C

1/8" Blade Attachment

With hair grain

1/4"

to

3/8"

 

Against hair grain

1/8"

to

1/4"

 

 

 

 

 

1/4" Blade Attachment

With hair grain

3/8"

to

1/2"

 

Against hair grain

1/4"

to

3/8"

 

 

 

 

 

3/8" Blade Attachment

With hair grain

1/2"

to

5/8"

 

Against hair grain

3/8"

to

1/2"

 

 

 

 

 

1/2" Blade Attachment

With hair grain

5/8"

to

7/8"

 

Against hair grain

1/2"

to

5/8"

 

ha caído en el agua. Devuelva el artefacto a una Centro de Servicio de Andis

 

para su verificación o reparación.

5.

Mantenga el cable eléctrico lejos de las superficies calentadas.

6.

Nunca deje caer ni inserte ningún objeto en ninguna abertura.

7.

No lo utilice al aire libre, ni lo opere donde se estén usando productos en

 

aerosol (nebulizados) o donde se esté administrando oxigeno.

8.

No utilice este artefacto con una hoja o peine dañado o roto, ya que se podrían

 

ocasionar lesiones en la piel.

9.

Para desconectar, coloque el control en la posición “off” y luego desconecte el

 

enchufe del tomacorriente.

DIAGRAMA A

DIAGRAMA B

SERVICIO DE REPARACIÓN EN FÁBRICA

Cuando las hojas de su Recortadora Andis pierdan el filo después de un uso repetido, se aconseja comprar un conjunto nuevo de hojas, disponible por medio de su Proveedor Andis o por medio de una de las Estaciones de Reparación Autorizada de Andis. Si desea que su recortadora también reciba servicio técnico, deberá empacarla cuidadosamente y enviarla ya sea por correo asegurado o por

U. P. S. a cualquiera de los Centros de Servicio.

GUÍA DE RECORTE

 

 

Longitud aproximada de corte

Descripción

Dirección de corte

Fino

 

Grueso

 

 

 

 

 

Hoja Andis estándar

Hacia el grano del cabello

1/16" (1.6mm)

a

3/16" (5mm)

 

Contra el grano del cabello

1/32" (0.8mm)

a

1/8" (3mm)

 

 

 

 

 

Hoja accesoria de 1/16"

Hacia el grano del cabello

3/16" (5mm)

a

5/16" (8mm)

 

Contra el grano del cabello

3/32" (2.5mm)

a

5/32" (4mm)

 

 

 

 

 

Hoja accesoria de 1/8"

Hacia el grano del cabello

1/4" (5mm)

a

3/8" (9.5mm)

 

Contra el grano del cabello

1/8" (3mm)

a

1/4" (5mm)

 

 

 

 

 

Hoja accesoria de 1/4"

Hacia el grano del cabello

3/8" (9.5mm)

a

1/2" (13mm)

reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

OPERATING INSTRUCTIONS

CAM

UPPER

BLADE

TENSION SPRING

5/8" Blade Attachment

With hair grain

3/4"

to

1"

 

Against hair grain

5/8"

to

7/8"

 

 

 

 

 

3/4" Blade Attachment

With hair grain

7/8"

to

1 1/8"

 

Against hair grain

3/4"

to

1"

GUARDE ESTAS INSTRUCCIONES

CAMBIO DEL JUEGO DE CUCHILLAS

Para quitar las cuchillas, primero desenchufe la maquinilla de la corriente eléctrica. Coloque la recortadora al revés, de forma que los dientes de la cuchilla queden hacia abajo. Quizá le sea más fácil

 

Contra el grano del cabello

1/4" (5mm)

a

3/8" (9.5mm)

 

 

 

 

 

Hoja accesoria de 3/8"

Hacia el grano del cabello

1/2" (13mm)

a

5/8" (16mm)

 

Contra el grano del cabello

3/8" (9.5mm)

a

1/2" (13mm)

 

 

 

 

 

Hoja accesoria de 1/2"

Hacia el grano del cabello

5/8" (16mm)

a

7/8" (22mm)

Please read the following instructions before using your new Andis Clipper. Give it the care that a fine precision built instrument deserves and it will give you years of service. Before starting clipper remove blade guard. Plug cord into electrical outlet, operate at 120 volt, 60 cycle AC electrical current or as noted on the unit. To start clipper move switch button to “on” position, to stop, move switch button back to original position. After using your Andis Clipper, rewrap cord and store in a safe place.

BOTTOM

 

 

BLADE

YOKE

BLADE SCREW

 

HOLES

 

 

DIAGRAM D

7/8" Blade Attachment

With hair grain

1"

to

1 1/4"

 

Against hair grain

7/8"

to

1 1/8"

 

 

 

 

 

1" Blade Attachment

With hair grain

1 1/8"

to

1 3/8"

 

Against hair grain

1"

to

1 1/4"

 

 

 

 

 

ESTE ARTEFACTO ESTÁ DESTINADO PARA USO COMERCIAL

Para reducir el riesgo de descargas eléctricas, este artefacto tiene un enchufe polarizado (una patilla es más ancha que la otra). Este enchufe encajará en un tomacorriente polarizado de una sola manera. Si el enchufe no puede insertarse completamente en el tomacorriente, invierta el enchufe. Si aún no puede insertarse, póngase en contacto con un electricista calificado para instalar el tomacorriente apropiado. No cambie el enchufe demanera alguna.

colocar la recortadora en una superficie plana para hacerlo. Saque los tornillos de las cuchillas (Diagrama C). Retire las cuchillas. Para reemplazar la hoja, colóquela nuevamente en posición mientras alinea el yugo de la hoja superior con la leva y el resorte de tensión de la recortadora (diagrama D). Alinee los orificios de los tornillos en la hoja inferior con los dos orificios en el soporte de la hoja, y vuelva a colocar los tornillos. No apriete demasiado los tornillos.

DIAGRAMA C

 

Contra el grano del cabello

1/2" (13mm)

a

5/8" (16mm)

 

 

 

 

 

Hoja accesoria de 5/8"

Hacia el grano del cabello

3/4" (19mm)

a

1" (25.4mm)

 

Contra el grano del cabello

5/8" (16mm)

a

7/8" (22mm)

 

 

 

 

 

Hoja accesoria de 3/4"

Hacia el grano del cabello

7/8" (22mm)

a

1-1/8" (28.5mm)

 

Contra el grano del cabello

3/4" (19mm)

a

1" (25.4mm)

 

 

 

 

 

Hoja accesoria de 7/8"

Hacia el grano del cabello

1" (25.4mm)

a

1-1/4" (32mm)

 

Contra el grano del cabello

7/8" (22mm)

a

1-1/8" (28.5mm)

 

 

 

 

 

Hoja accesoria de 1"

Hacia el grano del cabello

1-1/8" (28.5mm)

a

1-3/8" (34.9mm)

 

Contra el grano del cabello

1" (25.4mm)

a

1-1/4" (31.7mm)

 

 

 

 

 

Page 2
Image 2
Andis Company RACA warranty User Maintenance, Care and Servicing of Your Andis Clipper Blades, Factory Repair Service

RACA specifications

Andis Company, well-known for its grooming tools and appliances, has established a significant presence in the recreational and professional grooming markets. One of its standout products is the Andis RACA (Remote Animal Clipper Application), designed primarily for the needs of pet groomers and livestock handlers. This innovative tool embodies a blend of user-centric design, cutting-edge technology, and rugged performance.

The RACA is built around a unique ergonomic design that prioritizes comfort and usability during prolonged grooming sessions. Its lightweight structure reduces strain on the user’s wrist, allowing for extended operation without discomfort. The clipper is designed for versatile applications, making it suitable for a wide range of animal types, from household pets to larger livestock.

Equipped with advanced battery technology, the RACA offers cordless operation for ultimate freedom. This feature is particularly beneficial in environments where portability is critical. Users can enjoy extended run times without worrying about finding power sources, which is essential when working with large animals or in outdoor settings. The lithium-ion battery provides quick charging capabilities and maintains performance consistency, ensuring that groomers can rely on it for efficiency.

The RACA also boasts a range of customizable clipper blades to facilitate various grooming styles and coat types. This adaptability is a significant advantage, as it allows groomers to achieve precise results depending on the animal's needs. The clipper blades' quality construction ensures durability and sharpness, enhancing the overall grooming experience.

Furthermore, the RACA integrates noise-reducing technology, essential for sensitive animals that may become anxious during grooming. This feature significantly minimizes stress for pets and livestock, resulting in a calmer grooming experience for both the animal and the handler.

Maintenance is another area where the Andis RACA excels. The clipper is designed for easy cleaning and upkeep, ensuring longevity and sustained performance over time. This ease of maintenance allows groomers to focus more on their craft rather than spending excessive time on tool care.

In conclusion, the Andis RACA represents a significant advancement in grooming technology, merging the needs of professionals and animals alike. With its ergonomic design, advanced battery technology, customizable blades, noise reduction, and ease of maintenance, this clipper exemplifies Andis Company's commitment to quality and innovation in the grooming industry. Its robust features make it an indispensable tool for both pet groomers and livestock handlers.