|
|
| Date: February 26, 2014 No. | |
|
|
| Replaces | |
|
|
|
| |
Model | Description | Serial Number Range |
| |
920013 | Ariens ST22LE Compact | 124912 | – 124935, 124937 – 125008, 125037 – 125060, |
|
| 125094 | – 125271 |
| |
|
|
|
|
|
920014 | Ariens ST24LE Compact | 142966 | – 142999, 143264 – 143272, 143274 – 143281, |
|
| 143284 | – 143287, 143289, 143291 – 143304, 143306 – 143309, |
| |
|
| 143313 | – 143432, 143434 – 143435, 143439 – 143445, 143448, |
|
|
| 143450 | – 143462, 143466 – 143467, 143469 – 143496, 143500, |
|
|
| 143502 | – 143506, 143511, 143513 – 143518, 143520 – 143535, |
|
|
| 143700 | – 143728 |
|
|
|
|
| |
920021 | Ariens ST22LE Compact | 3089 – 3100, 3510 – 3940, 3942 – 4360, 4363, 4365 – 4372, |
| |
| 4374 – 4377, 4382 – 4384, 4386, 4389 – 4398, 4400, 4404 – 4405, |
| ||
|
| 4409, 4411 – 4415, 4418 – 4593, 4595 – 4617, 4619 – 4621, 4623 – |
| |
|
| 5815, 5817, 5819 – 5847, 5849 – 5883, 5885 – 5886, 5893 – 5895, |
| |
|
| 5899, 6000 – 6151, 6153 – 6172 |
| |
|
|
|
| |
920022 | Ariens ST24LET | 531 – 576, 701 – 712 |
| |
| Compact Track Sno – |
|
|
|
| Thro |
|
|
|
920402 | 143967 | – 145036, 145062, 145095, 145097, 145500 – 145591, |
| |
|
| 145593 | – 145594, 145596, 145598 – 145699, 146057 |
|
920403 | 126501 | – 127141, 127143 – 127145, 127185, 127197 – 127237, |
| |
|
| 127241 | – 127291, 127293 – 127326, 127328 – 127338, |
|
|
| 127340 | – 127341 |
|
|
|
|
| |
921025 | Ariens | 40600 – 40660 |
| |
| Brush |
|
|
|
|
|
|
| |
921026 | Gravely | 40061 – 40079 |
| |
| Season Brush |
|
|
|
921313 | Ariens 28” Brush – CE | 40163 – 40174 |
| |
939401 | 90112, 90140 – 90619, 90621 – 90623 |
|
ATTACHMENT DRIVE BELT PULLEY REPLACEMENT – SNO-THRO & SNO-TEK MODELS
Models 920013, 920014, 920021, 920022, 920402, 920403, 939401
Remove Attachment Drive Belt (Figures 1, 2 and 3)
1.Shut off engine, remove key, disconnect spark plug wire and allow unit to cool completely.
2.Loosen the hardware securing belt cover to unit.
NOTE: DO NOT completely remove the hardware from unit.
3.Remove belt cover.
4.Remove gear cover from top of chute pedestal.
5.Remove spring clip pin from chute crank and separate.
6.Remove remote deflector control cable from control lever if equipped).
7.Remove belt finger by removing cap screws mounting belt finger to engine (Figure 2).
8.Remove attachment drive belt from engine sheave (it may be necessary to turn engine sheave using recoil starter handle).
Page 2 of 8