![](/images/new-backgrounds/1052325/5232513x1.webp)
User Manual
Table summarising error codes
|
| Green Leds |
|
|
|
|
|
| Reset |
| Note | |
| Temperature indicator |
|
|
|
| Description | ❍ = flashing light | |||||
|
|
|
|
|
| |||||||
40 | 50 | 60 | 70 | 80 | 90 | yellow | red |
|
| ● = lit | ||
|
|
|
|
| ● |
|
|
| ● | X | Overheat |
|
● | ● |
|
|
|
|
|
|
| ● | X | Insufficient circulation |
|
| ● | ● |
|
|
| ● |
|
| Insufficient water (request filling) | |||
|
| ● | ● |
|
| ● |
|
| C.H. Flow temp. probe circuit open / short circuit | |||
|
|
| ● | ● |
| ● |
|
| C.H. Return temp. probe circuit open / short circuit | |||
● |
| ● |
|
|
| ● |
|
| External sensor circuit open / short circuit | |||
● |
|
| ● |
|
| ● |
|
| Floor thermostat contact open | |||
|
| ● | ● |
|
|
|
|
| ● | X | Heating delivery probe problem | |
● | ● |
|
|
|
| ● |
|
| Insufficient circulation |
| ||
|
|
| ● |
|
| ● |
|
| EEPROM error |
| ||
|
|
|
| ● |
| ● |
|
| Communication error |
| ||
● | ● | ● | ● | ● |
| ● |
|
| Too many (> 5) resets in 15 minutes | |||
|
|
|
| ● |
|
|
|
| ● | X | Main P.C.B. error |
|
● |
| ● |
|
|
| ● |
|
| Room sensor circuit open / short circuit | |||
|
|
|
|
|
|
|
|
| ● | X | No flame detected |
|
| ● | ● | ● |
|
| ● |
|
| Flame detected with gas valve closed | |||
|
| ● | ● | ● |
|
|
|
| ● | X | Flame lift |
|
● |
| ● |
| ● |
| ● |
|
| 1st Ignition Failed |
| ||
| ● | ● |
| ● |
| ● |
|
| 2nd Ignition Failed |
| ||
|
| ● | ● | ● |
| ● |
|
| Flame |
| ||
|
|
| ● | ● |
|
|
|
| ● | X | Thermofuse open |
|
| ● | ● |
|
|
|
|
|
| ● | X | Fan speed error |
|
Anti-frost Device.
When the electrical supply is turned on, the
If the primary circuit temperature is between 3°C and 8°C the pump will run (with the diverter valve switching between central heating and hot water every 1 minute) until the temperature reaches > 9°C.
If the flow temperature remains between 3°C and 8°C the pump will continue to run for a maximum of 20 minutes unless a temperature above > 9°C is detected in the central heating flow, after this the burner will fire (heating position) until a temperature of > 30°C is detected.
If the central heating flow temperature is < 3°C, the burner will fire (heating position) at minimum power until the temperature reaches > 30°C, the burner will go out.
If lockout is caused by overheat the burner will not fire but the pump will continue to run (heating position).
The
-the system pressure is correct;
-the boiler is electrically powered;
-there is a supply of gas.
Change of gas type
Our boilers are designed to function either with Natural Gas (meth- ane) or L.P.G. gas. If you need to change from one gas to the other, one of our Authorised Service Centres must be contacted to convert the appliance.
Maintenance
Schedule an annual maintenance
Correct maintenance generally results in savings in the cost of run- ning the system.
Failure to arrange an annual service for the appliance will invalidate the second year of the manufacturer’s guarantee.
7