|
|
| 11 |
|
|
| ||
|
|
|
|
|
|
| .outlet | |
| electric the from unit the unplugging and once button “On/Off” the pressing by | |||||||
| cycle cooking the during anytime at stopped be can settings preset The :Note | |||||||
|
| .unit the from end magnetic the remove then and | ||||||
| outlet electric the from cord the unplug frying, discontinue to wish you If .five | |||||||
| and four three, steps repeat and desired is food same the of batch another | |||||||
| if setting previous the repeat to once button On/Off the Press .away drain | |||||||
| to oil excess allow to hooks drain on place and oil the of out up basket the Lift .5 | |||||||
| .used just you that code program the read will display | |||||||
| LCD The .beeps three hear will you course, its run has time preset the After .4 | |||||||
| .once control time/temperature the press time, check To .reading temperature | |||||||
| to back default will display The .timer countdown the begin to button “On/Off” | |||||||
| the press and oil the into slowly food the Lower .pause will unit the and | |||||||
flash will light “Heat” green The .times 3 beep will it preheated, is oil the Once .3 | ||||||||
|
| .preheating is oil the that indicate to illuminate | ||||||
| will light “Heat” green The | .oil the preheat to button “On/Off” the Press .2 | ||||||
|
|
|
|
|
|
| .time same | |
|
|
|
|
|
|
| the at buttons | |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| and | |
|
|
|
|
|
|
| “Time/Temp” | |
|
|
|
|
|
| |||
|
|
|
|
|
|
| the Press | |
|
|
|
|
|
|
| .12 page | |
| on chart the in outlined as unit the into programmed automatically be will time | |||||||
| and temperature the setting, preset a selected have you Once .use to want | |||||||
| you setting correct the find to |
|
| down or | up scroll can You .button | |||
| the using by use to going are you number preset the select page, next the | |||||||
| on chart the Following .set be to ready is unit the that signifies This .flashing | |||||||
| “00” the with “P00”, display will readout LED The .simultaneously buttons | |||||||
| and “Time/Temp” the press settings, preprogrammed the access To .1 | |||||||
|
| .settings these using before carefully directions all Read | ||||||
|
|
|
|
| Settings Preprogrammed the Using | |||
|
| USE TO HOW |
| |||||
|
|
|
|
|
|
|
|
|
CÓMO UTILIZAR
Uso de las configuraciones preprogramadas
Lea todas las instrucciones con cuidado antes de usar estas configuraciones.
1.Con el fin de tener acceso a las configuraciones preprogramadas, presione
los botones "Time/Temp" y en forma simultánea. La lectura LED mostrará "P00", donde "00" parpadeará. Esto significa que la unidad está lista para configurarse. Siguiendo la tabla de la página siguiente, seleccione
el número preconfigurado que va a utilizar presionando el botón . Usted
puede recorrer hacia arriba o hacia abajo para encontrar la configuración correcta que desea usar. Una vez que haya seleccionado una configuración preprogramada, la temperatura y el tiempo se programarán automáticamente en la unidad conforme se indica en la tabla de la página 12.
Presione los botones
"Time/Temp" y | al |
mismo tiempo. |
|
2.Presione el botón "On/Off" para precalentar el aceite. La luz verde "heat" (calentar) se encenderá para indicar que el aceite se está precalentando.
3.Una vez que el aceite esté precalentado, escuchará 3 pitidos. La luz verde "heat" (calentar) parpadeará y la unidad hará una pausa. Sumerja lentamente el alimento en el aceite y presione el botón "On/Off" para iniciar el conteo regresivo del reloj. La pantalla volverá por defecto a la lectura de temperatura. Para verificar el tiempo, presione el control de tiempo/temperatura una vez.
4.Después de que el tiempo preprogramado haya transcurrido, escuchará tres pitidos. La pantalla LCD indicará el código del programa que acaba de usar.
5.Saque la canasta del aceite y colóquela en los ganchos para escurrir con el fin de que el exceso de aceite se escurra. Presione el botón On/Off una vez para repetir la configuración anterior si desea freír otro lote del mismo alimento y repita los pasos 3, 4 y 5. Si desea dejar de freír, desconecte el cable de la toma de corriente eléctrica y luego retire el conector magnético de la unidad.
Nota: Las configuraciones preprogramadas se pueden detener en cualquier momento durante el ciclo de cocción al presionar el botón "On/Off" una vez y desconectando la unidad de la toma de corriente eléctrica.
11