5
|
|
|
|
| .helado |
| |
hacer para máquina la uso en esté mientras necesario, es si menudo a más o |
| ||||||
minutos, 15 ó 10 cada plástico de agitador el Utilice .hielo el y sal la juntos mezcle y |
| ||||||
revuelva vueltas, dé bote el Mientras .motor el funcionar a ponga o manivela la Gire | .13 | ||||||
.piedra de sal y hielo más agregue pulgadas, 3 a 2 de derrita se hielo el Conforme | .12 | ||||||
|
|
|
|
| .drenaje de agujero |
| |
el con iguale se agua del superior parte el que hasta cubeta la a frío agua Agregue | .11 | ||||||
|
|
|
|
| .drenaje |
| |
| de agujero del nivel al llegue sal y hielo el que hasta 9 y 8 tramites los Repite | .10 | |||||
.aproximadamente) taza (1/4 hielo del encima piedra de sal de capa una Agregue | .9 | ||||||
|
|
|
| .hielo de medianas bolsas 2 o |
| ||
1 usar espera se helado, del bote cada Para .gruesos y pequeños pedazos en hielo |
| ||||||
el romper para martillo un o mazo un usar necesite vez Tal .gruesas y pequeñas |
| ||||||
piezas en quebrado esté cubeta la en ponga usted que hielo el que Asegúrese |
| ||||||
.aproximadamente) tazas (6 hielo de capa una con madera de cubeta la Llene | .8 | ||||||
.eléctrico motor el usando está si tomacorriente el en eléctrico cordón el Conecte | .7 | ||||||
|
|
|
|
|
|
|
|
| 6 Dibujo |
| 5 Dibujo |
| 4 Dibujo |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5 Dibujo“ |
| .”) |
| 3 Dibujo |
|
| ||
| (vea manivela la a y/o motor al ajustada quede tapadera |
|
| ||
|
|
|
| ||
|
| la que para mano la con bote el rotar necesite vez (tal motor |
|
| |
|
| del o manual manivela la de redondeado extremo el sobre pase |
|
| |
|
| alambre de cerrojo el que de fin a cerrojo el levante Suavemente |
|
| |
|
| “ (vea cerrojo el está donde abierto, extremo |
|
| |
|
| del dentro caerá manivela la de opuesto4 Dibujoextremo“ El .”) | |||
|
| (vea cubeta la de borde de rectangular agujero el en eléctrico |
|
| |
|
| motor el o manual manivela la de rectangular extremo el Deslice | .6 |
| |
|
| “ (vea cubeta la de centro el en encaje cono |
|
| |
|
| el que de asegúrese y madera de cubeta la en bote el Coloque | .5 |
| |
|
|
| |||
|
|
|
|
| |
|
|
| helado: hacer Para | ||
| APARATO SU USAR COMO |
|
|
USING YOUR ICE CREAM MAKER
To Make Ice Cream:
5.Place the mixing canister in the wooden bucket and make sure it engages the cone in the center of the bucket (see “Figure 3”).
6.Slide the rectangular end of the hand crank or electric motor into the rectangular hole on the rim of the bucket (see “Figure 4”). The opposite end of the crank or motor will drop into the open end, where the latch is located (see “Figure 6”). Gently lift the latch so that the wire goes over the rounded end of the hand crank or
motor. The mixing canister may need to be rotated by | Figure 3 | |
hand so that the lid fits into the motor/hand crank (see | ||
| ||
“Figure 5”). |
|
|
|
|
|
|
Figure 4 |
| Figure 5 |
| Figure 6 |
7.If you are using the electric motor, plug the power cord into a working electrical outlet.
8.Fill the wooden bucket with a small layer of ice (about 6 cups), evenly distributed around the base of the canister. Be sure that the ice added into the bucket is broken into small, coarse pieces. A mallet or hammer may be used to break the ice into smaller pieces, if needed. For each batch of ice cream, expect to use
9.Cover the first layer of ice evenly with a thin layer of rock salt (about 1/2 cup).
10.Repeat steps 8 through 9, layering the ice and salt until it reaches the bottom of the drainage hole on the side of the wood bucket.
NOTE:
• Adding more ice will cause the mixture to leak out of the drainage hole.
11. | Add cold water to the6 Dibujoice/salt mixture.”) | until the water level reaches the bottom of the |
| drainage hole. |
|
12. | As the ice melts down 2 to 3 inches, you may add more ice and more rock salt to the | |
| mixture. |
|
13. | Begin cranking with3 Dibujothe hand crank.”) mechanism or turn on the electric motor. As the | |
| mixing canister turns, stir and mix the salt and ice together. Use the plastic stirrer | |
| every |
5