Asante Technologies 39240, 480 - page 128

3) spanning-tree forceversion none

This command selects none spanning tree type.

Format spanning-t ree forceversion none

Mode Global Config

10.4.110.2 spanning-tree configuration

This command configures MSTP region name and rev ision.

1) spanning-tree configuration name

This command configure s MSTP region name (Max.32 chars).

Format spanning-t ree configuration name <WORD>

Mode Global Config

2) spanning-tree configuration revision

This command configure s revision level.

Format spanning-t ree s configuration revision <0-655 35>

Mode Global Config

10.4.110.3 spanning-tree forward-time

This configures the bridge forward delay parameter.

Format spanning-t ree forward-time <4-30>

Mode Global Config

10.4.110.4 spanning-tree max-age

This command configure s the bridge max age parameter.

Format spanning-t ree max-age <6-40>

Mode Global Config

10.4.110.5 spanning-tree max-hops

This command configure the number of hops in a region.

Format spanning-t ree max-hops <1-40>

Mode Global Config

10.4.110.6 spanning-tree port

1)spanning-tree port all

This command specifies RSTP capability for all ports.

Format spanning-t ree p ort all {enable |disable}

Mode Global Config

2)spanning-tree port cost

This command configure s RSTP port path cost.

Format spanning-t ree p ort cost <0-200000000>

Mode Global Config

3)spanning-tree port priority

37

This command configure s RSTP port priority.

Format spanning-t ree port priority <0-24>

Mode Global Config

4)spanning-tree port edge

This command configure s STP edge .

Format spanning-t ree port edge {enable|disable}

Mode Global Config

5)spanning-tree port force-p2plink

This command configure s force point to point link mode on ports.

Format spanning-t ree p ort force-p2plink {auto|ena ble|disable}

Mode Global Config

6)spanning-tree port migration-che ck

This command Re-checks the appropriate BPDU format to send on ports.

Format spanning-t ree p ort migration-check {enable|d i sable}

Mode Global Config

10.4.110.7 spanning-tree priority

This command configures RSTP bridge priority value.

Format spanning-t ree p riority <0-61440>

Mode Global Config

128 Asante IntraCore IC39240/480 User’s Manual

Contents

Main IntraCore 39240/480 Layer 2+ Gigabit Ethernet Switch Users Manual Table of Contents IntraCore 39240/480 Page Page Page Chapter 1: Introduction 1.1 Features 1.2 System Defaults Page Page Page Page 1.5 Management and Configuration Chapter 2: Hardware Installation and Setup 2.1 Installation Overview 2.1.1 Safety Overview 2.1.2 Recommended Installation Tools 2.1.3 Power Requirements 2.2 Installing into an Equipment Rack 2.2.1 Equipment Rack Guidelines 2.3 SFP Mini GBIC Ports 2.4 Connecting Power 2.5 Connecting to the Network 2.5.1 10/100/1000BaseT Ports Cabling Procedures Page Page Chapter 3: Initial Software Setup 3.1 Connecting to a Console Page 3.2 Connecting to a PC 3.3 Username and Password 3.4 Configuring an IP Address 3.5 Restoring Factory Defaults Chapter 4: Understanding the Command Line Interface (CLI) Privileged Top Mode: Switch# Interface Configuration Mode: Switch(interface #)# 4.1 User Top (User EXEC) Mode show ? 4.2 Privileged Top (Privileged EXEC) Mode COMMAND> enable Username : admin Password : xxxxxx Switch# 4.3 Global Configuration Mode 4.3.1 Interface Configuration Mode 4.4 Advanced Features Supported within the Command Mode Page 4.5 Using CLI Command History 4.6 Using Command-Line Editing Features and Shortcuts 4.6.1 Moving Around on the Command Line 4.6.2 Completing a Partial Command Name 4.6.3 Deleting Entries Chapter 5: Managing the System and Configuration Files 5.1 Managing the System 5.1.1 Setting the System Clock 5.1.2 Specify the Hostname 5.1.5 Test Connections with Ping Tests 5.1.3 Enable the System Log 5.1.4 Displaying the Operating Configuration 5.2 Managing Configuration Files 5.2.1 Configuring from the Terminal 5.2.2 Copying Configuration Files to a Net work Server 5.2.3 Copying Configuration Files from a Network Server to the Switch 5.3 Managing system image Files 5.3.1 Saving System image to a Net work Server 5.3.2 Replacing Sy stem image from a Network Server 5.4 Configuring SNMP 5.4.1 Configuring SNMP Support 5.5 Spanning Tree Algorithm 5.5.1 Spanning Tree Parameters 5.5.2 Rapid Spanning Tree Protocol (RSTP) 5.5.3 Configuring spanning-tree Page Page Page Chapter 6: Configuring IP 6.1 Establish Address Resolution 6.2 Managing IP Multicast Traffic 6.2.1 IGMP Overview 6.2.2 Configuring IGMP Page 6.3 Access Lists 6.3.1 Creating an Access List 6.3.2 Configuring an Access List Page 6.3.3 Applying an Access List to an Interface 6.3.4 Enabling an Access List Chapter 7: VLAN Configuration 7.1 Creating or Modifying a VLAN 7.2 VLAN Port Membership 7.2.1 configuring vlan ports 7.2.2 Trunk (IEEE 802.1q) Page Chapter 8: Quality of Service Configuration 8.1 Scheduling algorithm 8.1.1 Configuring Weighted Round Robin 8.1.2 Monitoring Weighted Round Ro bin 8.2 Priority Queuing 8.2.1 Priority Mapping 8.2.2 Port Based QOS 8.2.3 802.1P Based QOS 8.2.4 IP Based QOS 8.3 Traffic Shaping 8.3.1 Configuring Traffic Shaping for an Interface 8.4 Rate Limiting Chapter 9: Configuring the Switch Using the GUI 9.1 Main Configuration Menu 9.2 System 9.2.1 System System Information 9.2.2 System Network management Page 9.2.3 System Time Setting Page Page Port management LACP Property Port Management LACP Property Port. Port Management LAG Group. Port Management LAG Group - Each Group. 9.4 VLAN Management. Page VLAN MANAGEMENT VLAN PORT. 9.5 Spanning Tree Page Page Page 9.6 Multicast. Static multicast settings can be set. Port by port participation can be controlled. IGMP 9.7 Security - Port Security. Each port can be listed individually or a table can be displ ayed using the Show Table button Page TACAS+ and Storm Control are available on the next screens. Page Page DSCP 802.1P Port-based QoS Rate Control 9.9 SNMP SNMP Continued Page Page Page Page Page Page ADMIN Continued Page Page Page Page DHCP Relay/ DCP Option 82 these screens control the relay of DHCP information from a server. Page Page Page Page 9.13 Help General help is available for many screens. Page Chapter 10: CLI Commands 10.1 Modes 10.2 User Mode commands 10.3 Privileged Mode commands Page Page Page Page Page Page 10.4 Global Config mode commands Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 10.5 Interface Config mode commands Page Page Page Page Appendix A: Basic Troubleshooting Appendix B: Specifications TECHNICAL SPECIFICATIONS Interfaces Status Indicators Performance Specifications Page Standards Compliance L2+ Management Specification s Network Standards Physical Environmental Specifications System Requirements Modules Security Package Content Warranty Asante Service Appendix C: FCC Compliance and Warranty Statements C.1 FCC Compliance Statement C.2 Important Safety Instructions Page Index