Asante Technologies 39240, 480 - page 129

10.4.110.8 spanning-tree mst

Configure a multiple spanning tree instance.

1) spanning-tree mst instance

This command creates or removes a MST inst ance

spanning-tree mst instance add

This command creates a MST instan ce.

Format spanning-t ree mst instance add vlan <vlan list> mstpid <MST ID>

Mode Global Config

e.g. Switch(Config)# Spanning-Tree mst instance add vlan 2-5 mstpid 2

Switch(Config)# Spanning -Tree mst in stance add vlan 6 mstpid 3

spanning-tree mst instan ce delete

This command removes the last MST instance.

Format spanning-t ree mst instance delete

Mode Global Config

2 )spanning-tree mst vlan

This command adds or deletes vlan frome a MSTP instance.

spanning-tree mst vl an <MST ID> <vlan list> add

This command creates a MST instan ce.

Format spanning-t ree mst vlan <MST ID> <vlan list> add

Mode Global Config

e.g. Switch(Config)# Spanning-Tree mst vlan 3 3-5 add

Spanning-Tree mst vlan <MST ID> <vlan list> delete

This command deletes a vlan from a MS T instance.

Format Spanning-Tree mst vlan <MST ID> < vlan list> delete

Mode Global Config

38

3) spanning-tree mst bridgepri

This command configure s bridge priority for a MST instance.

Format spanning-t ree mst bridgepri <MST ID> <priority>

Mode Global Config

4) spanning-tree mst cost

This command configure s port path cost in a MST instance.

Format spanning-t ree mst cost <MST ID> <path cost> ports <port list>

Mode Global Config

5)spanning-tree mst priority

This command configure s port priority in a MST instance

Format spanning-tree mst priority <MST ID> <priority> ports <port list>

Mode Global Config

10.4.20 User commands

This command changes user pass word.

Format user password

Mode Global Config

10.4.21 Interface commands

This command enters into configure inte rface mode.

Format Interface <port-ID>

Mode Global Config

10.4.22 rmon

This command is used to configure RMON.

10.4.22.1 rmon event

This command creates rmon event entry.

Format rmon event index < 1..65535 > desc <WORD> event <1..4>

community <WORD>owner<WORD>

Mode Global Config

e.g. Switch(Config)# rmon event index 1 desc 123 event 4 community 123

owner test

10.4.22.2 rmon alarm

129 Asante IntraCore IC39240/480 User’s Manual

Contents

Main IntraCore 39240/480 Layer 2+ Gigabit Ethernet Switch Users Manual Table of Contents IntraCore 39240/480 Page Page Page Chapter 1: Introduction 1.1 Features 1.2 System Defaults Page Page Page Page 1.5 Management and Configuration Chapter 2: Hardware Installation and Setup 2.1 Installation Overview 2.1.1 Safety Overview 2.1.2 Recommended Installation Tools 2.1.3 Power Requirements 2.2 Installing into an Equipment Rack 2.2.1 Equipment Rack Guidelines 2.3 SFP Mini GBIC Ports 2.4 Connecting Power 2.5 Connecting to the Network 2.5.1 10/100/1000BaseT Ports Cabling Procedures Page Page Chapter 3: Initial Software Setup 3.1 Connecting to a Console Page 3.2 Connecting to a PC 3.3 Username and Password 3.4 Configuring an IP Address 3.5 Restoring Factory Defaults Chapter 4: Understanding the Command Line Interface (CLI) Privileged Top Mode: Switch# Interface Configuration Mode: Switch(interface #)# 4.1 User Top (User EXEC) Mode show ? 4.2 Privileged Top (Privileged EXEC) Mode COMMAND> enable Username : admin Password : xxxxxx Switch# 4.3 Global Configuration Mode 4.3.1 Interface Configuration Mode 4.4 Advanced Features Supported within the Command Mode Page 4.5 Using CLI Command History 4.6 Using Command-Line Editing Features and Shortcuts 4.6.1 Moving Around on the Command Line 4.6.2 Completing a Partial Command Name 4.6.3 Deleting Entries Chapter 5: Managing the System and Configuration Files 5.1 Managing the System 5.1.1 Setting the System Clock 5.1.2 Specify the Hostname 5.1.5 Test Connections with Ping Tests 5.1.3 Enable the System Log 5.1.4 Displaying the Operating Configuration 5.2 Managing Configuration Files 5.2.1 Configuring from the Terminal 5.2.2 Copying Configuration Files to a Net work Server 5.2.3 Copying Configuration Files from a Network Server to the Switch 5.3 Managing system image Files 5.3.1 Saving System image to a Net work Server 5.3.2 Replacing Sy stem image from a Network Server 5.4 Configuring SNMP 5.4.1 Configuring SNMP Support 5.5 Spanning Tree Algorithm 5.5.1 Spanning Tree Parameters 5.5.2 Rapid Spanning Tree Protocol (RSTP) 5.5.3 Configuring spanning-tree Page Page Page Chapter 6: Configuring IP 6.1 Establish Address Resolution 6.2 Managing IP Multicast Traffic 6.2.1 IGMP Overview 6.2.2 Configuring IGMP Page 6.3 Access Lists 6.3.1 Creating an Access List 6.3.2 Configuring an Access List Page 6.3.3 Applying an Access List to an Interface 6.3.4 Enabling an Access List Chapter 7: VLAN Configuration 7.1 Creating or Modifying a VLAN 7.2 VLAN Port Membership 7.2.1 configuring vlan ports 7.2.2 Trunk (IEEE 802.1q) Page Chapter 8: Quality of Service Configuration 8.1 Scheduling algorithm 8.1.1 Configuring Weighted Round Robin 8.1.2 Monitoring Weighted Round Ro bin 8.2 Priority Queuing 8.2.1 Priority Mapping 8.2.2 Port Based QOS 8.2.3 802.1P Based QOS 8.2.4 IP Based QOS 8.3 Traffic Shaping 8.3.1 Configuring Traffic Shaping for an Interface 8.4 Rate Limiting Chapter 9: Configuring the Switch Using the GUI 9.1 Main Configuration Menu 9.2 System 9.2.1 System System Information 9.2.2 System Network management Page 9.2.3 System Time Setting Page Page Port management LACP Property Port Management LACP Property Port. Port Management LAG Group. Port Management LAG Group - Each Group. 9.4 VLAN Management. Page VLAN MANAGEMENT VLAN PORT. 9.5 Spanning Tree Page Page Page 9.6 Multicast. Static multicast settings can be set. Port by port participation can be controlled. IGMP 9.7 Security - Port Security. Each port can be listed individually or a table can be displ ayed using the Show Table button Page TACAS+ and Storm Control are available on the next screens. Page Page DSCP 802.1P Port-based QoS Rate Control 9.9 SNMP SNMP Continued Page Page Page Page Page Page ADMIN Continued Page Page Page Page DHCP Relay/ DCP Option 82 these screens control the relay of DHCP information from a server. Page Page Page Page 9.13 Help General help is available for many screens. Page Chapter 10: CLI Commands 10.1 Modes 10.2 User Mode commands 10.3 Privileged Mode commands Page Page Page Page Page Page 10.4 Global Config mode commands Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 10.5 Interface Config mode commands Page Page Page Page Appendix A: Basic Troubleshooting Appendix B: Specifications TECHNICAL SPECIFICATIONS Interfaces Status Indicators Performance Specifications Page Standards Compliance L2+ Management Specification s Network Standards Physical Environmental Specifications System Requirements Modules Security Package Content Warranty Asante Service Appendix C: FCC Compliance and Warranty Statements C.1 FCC Compliance Statement C.2 Important Safety Instructions Page Index