Asante Technologies 39240, 480 2.3 SFP Mini GBIC Ports

1. Place the switch on a flat, stable surface.

2. Locate a rack-mounting bracket (supplied) and place it over the mounting holes on one side of the switch.

3. Use the screws (supplied) to secure the bra cket (with a Phillips screwdriver).

4. Repeat the two previous steps on the other side of the switch.

5. Place the switch in the equipment rack.

6. Secure the switch by securing its mounting b rackets onto the equipme nt rack with the appropriate screws

(supplied).

Important: Make sure the switch is supported until all the mounting screws for each bracket are secured to the

equipment rack. Failure to do so could caus e the switch to fall, which may result in personal injury or damage to the

switch.

2.2.1 Equipment Rack Guidelines

Use the following guidelines to ensure that the switch will fit safely within the equipment rack:

• Size: 17.5 x 12.7 x 1.8 inches (440 x 234 x 45 mm)

• Ventilation: Ensure that the rack is installed in a room in which the temperature remains below 104° F (40° C). Be

sure that no obstructions, such as other equipment or cables, block airflow to or from the vents of the switch

• Clearance: In addition to providing clearance for ventilati on, ensure that adequate clearance for servicing the

switch from the front exists

2.3 SFP Mini GBIC Ports

The GBIC Interface is the industry standard for Gigabit Ethe rnet Interfaces.

The Gigabit SFP module insert s into the Mini GBIC port to create a new Gigabit port. The hot-swapping feature on

the IntraCore IC39240/480 lets you install and repl ace the SFP transceivers while the system is operating; you do not

need to disable the software or shut down the system power.

To install the module, do the following:

1. Insert the transceiver with the optical connector facing outward and the slot connector facing down. The module

is keyed to help establish the correct positi on .

2. Slide the SFP transceiver into the slot until it clicks into plac e.

3. Remove the module’s rubber port cap.

4. Connect the cable to the Gigabit SFP module’s port.

Caution: When replacing a SFP transceiver you must always disconnect the network cable before removing a

transceiver.

16 Asante IntraCore IC39240/480 User’s Manual

Contents

Main IntraCore 39240/480 Layer 2+ Gigabit Ethernet Switch Users Manual Table of Contents IntraCore 39240/480 Page Page Page Chapter 1: Introduction 1.1 Features 1.2 System Defaults Page Page Page Page 1.5 Management and Configuration Chapter 2: Hardware Installation and Setup 2.1 Installation Overview 2.1.1 Safety Overview 2.1.2 Recommended Installation Tools 2.1.3 Power Requirements 2.2 Installing into an Equipment Rack 2.2.1 Equipment Rack Guidelines 2.3 SFP Mini GBIC Ports 2.4 Connecting Power 2.5 Connecting to the Network 2.5.1 10/100/1000BaseT Ports Cabling Procedures Page Page Chapter 3: Initial Software Setup 3.1 Connecting to a Console Page 3.2 Connecting to a PC 3.3 Username and Password 3.4 Configuring an IP Address 3.5 Restoring Factory Defaults Chapter 4: Understanding the Command Line Interface (CLI) Privileged Top Mode: Switch# Interface Configuration Mode: Switch(interface #)# 4.1 User Top (User EXEC) Mode show ? 4.2 Privileged Top (Privileged EXEC) Mode COMMAND> enable Username : admin Password : xxxxxx Switch# 4.3 Global Configuration Mode 4.3.1 Interface Configuration Mode 4.4 Advanced Features Supported within the Command Mode Page 4.5 Using CLI Command History 4.6 Using Command-Line Editing Features and Shortcuts 4.6.1 Moving Around on the Command Line 4.6.2 Completing a Partial Command Name 4.6.3 Deleting Entries Chapter 5: Managing the System and Configuration Files 5.1 Managing the System 5.1.1 Setting the System Clock 5.1.2 Specify the Hostname 5.1.5 Test Connections with Ping Tests 5.1.3 Enable the System Log 5.1.4 Displaying the Operating Configuration 5.2 Managing Configuration Files 5.2.1 Configuring from the Terminal 5.2.2 Copying Configuration Files to a Net work Server 5.2.3 Copying Configuration Files from a Network Server to the Switch 5.3 Managing system image Files 5.3.1 Saving System image to a Net work Server 5.3.2 Replacing Sy stem image from a Network Server 5.4 Configuring SNMP 5.4.1 Configuring SNMP Support 5.5 Spanning Tree Algorithm 5.5.1 Spanning Tree Parameters 5.5.2 Rapid Spanning Tree Protocol (RSTP) 5.5.3 Configuring spanning-tree Page Page Page Chapter 6: Configuring IP 6.1 Establish Address Resolution 6.2 Managing IP Multicast Traffic 6.2.1 IGMP Overview 6.2.2 Configuring IGMP Page 6.3 Access Lists 6.3.1 Creating an Access List 6.3.2 Configuring an Access List Page 6.3.3 Applying an Access List to an Interface 6.3.4 Enabling an Access List Chapter 7: VLAN Configuration 7.1 Creating or Modifying a VLAN 7.2 VLAN Port Membership 7.2.1 configuring vlan ports 7.2.2 Trunk (IEEE 802.1q) Page Chapter 8: Quality of Service Configuration 8.1 Scheduling algorithm 8.1.1 Configuring Weighted Round Robin 8.1.2 Monitoring Weighted Round Ro bin 8.2 Priority Queuing 8.2.1 Priority Mapping 8.2.2 Port Based QOS 8.2.3 802.1P Based QOS 8.2.4 IP Based QOS 8.3 Traffic Shaping 8.3.1 Configuring Traffic Shaping for an Interface 8.4 Rate Limiting Chapter 9: Configuring the Switch Using the GUI 9.1 Main Configuration Menu 9.2 System 9.2.1 System System Information 9.2.2 System Network management Page 9.2.3 System Time Setting Page Page Port management LACP Property Port Management LACP Property Port. Port Management LAG Group. Port Management LAG Group - Each Group. 9.4 VLAN Management. Page VLAN MANAGEMENT VLAN PORT. 9.5 Spanning Tree Page Page Page 9.6 Multicast. Static multicast settings can be set. Port by port participation can be controlled. IGMP 9.7 Security - Port Security. Each port can be listed individually or a table can be displ ayed using the Show Table button Page TACAS+ and Storm Control are available on the next screens. Page Page DSCP 802.1P Port-based QoS Rate Control 9.9 SNMP SNMP Continued Page Page Page Page Page Page ADMIN Continued Page Page Page Page DHCP Relay/ DCP Option 82 these screens control the relay of DHCP information from a server. Page Page Page Page 9.13 Help General help is available for many screens. Page Chapter 10: CLI Commands 10.1 Modes 10.2 User Mode commands 10.3 Privileged Mode commands Page Page Page Page Page Page 10.4 Global Config mode commands Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 10.5 Interface Config mode commands Page Page Page Page Appendix A: Basic Troubleshooting Appendix B: Specifications TECHNICAL SPECIFICATIONS Interfaces Status Indicators Performance Specifications Page Standards Compliance L2+ Management Specification s Network Standards Physical Environmental Specifications System Requirements Modules Security Package Content Warranty Asante Service Appendix C: FCC Compliance and Warranty Statements C.1 FCC Compliance Statement C.2 Important Safety Instructions Page Index