Asante Technologies 39240, 480 - page 136

and 0 means no limit.

Format storm-control broadcast <rate>

Mode Interface Config

10.5.14.3 storm-control broadcast-mu lticast

This command storm control limited

value :0,64,256,1024,10240,65536.102400,1024000,which the unit is Kbps

and 0 means no limit.

Format storm-control broadcast-multicast <rate>

Mode Interface Config

10.5.14.4 storm-control broadcast-un known

This command storm control limited

value :0,64,256,1024,10240,65536.102400,1024000,which the unit is Kbps

and 0 means no limit.

Format storm-control broadcast-unknown <rate>

Mode Interface Config

e.g. Switch(Interface 1)# storm-control broadca st-unknown 64

10.5.14.5 storm-control all-cast

This command storm control limited

value :0,64,256,1024,10240,65536.102400,1024000,which the unit is Kbps

and 0 means no limit.

Format storm-control all-ca st <rate>

Mode Interface Config

10.5.15 rmon-counter command

This command specifies rmon counter capability on a port

Format rmon-counter {ena ble|disable}

Mode Interface Config

10.5.16 set igmp-router-port comma nd

This command specifies igmp router port .

Format set igmp-router-port {ebable|disable}

Mode Interface Config

10.5.17 spanning-tree command

10.5.17.1 spanning-tree cost

This command configure RSTP port path cost, path cost value:0~200000000.

Format spanning-t ree cost <pathcost>

Mode Interface Config

10.5.17.2 spanning-tree edge

This command configure e dge property

Format spanning-t ree e dge {enable|disable}

Mode Interface Config

e.g. Switch(Interface 1)# spanning-tree edge enable

47

10.5.17.3 spanning-tree force-p2plink

This command configure fo rce point to point link mode.

Format spanning-t ree force-p2 plink {auto|enable|disable}

Mode Interface Config

10.5.17.4 spanning-tree migration-check

This command re-checks the appropriate BPDU format to send on this port

Format spanning-t ree mig ration-check {enable|disable}

Mode Interface Config

10.5.17.5 spanning-tree mst

This command configures multiple spanning tree instance.

1) spanning-tree mst cost

This command configure the path cost on a MST instance :1~200000000.

Format spanning-t ree mst cost <pathcost>

Mode Interface Config

2) spanning-tree mst priority

136 Asante IntraCore IC39240/480 User’s Manual

Contents

Main IntraCore 39240/480 Layer 2+ Gigabit Ethernet Switch Users Manual Table of Contents IntraCore 39240/480 Page Page Page Chapter 1: Introduction 1.1 Features 1.2 System Defaults Page Page Page Page 1.5 Management and Configuration Chapter 2: Hardware Installation and Setup 2.1 Installation Overview 2.1.1 Safety Overview 2.1.2 Recommended Installation Tools 2.1.3 Power Requirements 2.2 Installing into an Equipment Rack 2.2.1 Equipment Rack Guidelines 2.3 SFP Mini GBIC Ports 2.4 Connecting Power 2.5 Connecting to the Network 2.5.1 10/100/1000BaseT Ports Cabling Procedures Page Page Chapter 3: Initial Software Setup 3.1 Connecting to a Console Page 3.2 Connecting to a PC 3.3 Username and Password 3.4 Configuring an IP Address 3.5 Restoring Factory Defaults Chapter 4: Understanding the Command Line Interface (CLI) Privileged Top Mode: Switch# Interface Configuration Mode: Switch(interface #)# 4.1 User Top (User EXEC) Mode show ? 4.2 Privileged Top (Privileged EXEC) Mode COMMAND> enable Username : admin Password : xxxxxx Switch# 4.3 Global Configuration Mode 4.3.1 Interface Configuration Mode 4.4 Advanced Features Supported within the Command Mode Page 4.5 Using CLI Command History 4.6 Using Command-Line Editing Features and Shortcuts 4.6.1 Moving Around on the Command Line 4.6.2 Completing a Partial Command Name 4.6.3 Deleting Entries Chapter 5: Managing the System and Configuration Files 5.1 Managing the System 5.1.1 Setting the System Clock 5.1.2 Specify the Hostname 5.1.5 Test Connections with Ping Tests 5.1.3 Enable the System Log 5.1.4 Displaying the Operating Configuration 5.2 Managing Configuration Files 5.2.1 Configuring from the Terminal 5.2.2 Copying Configuration Files to a Net work Server 5.2.3 Copying Configuration Files from a Network Server to the Switch 5.3 Managing system image Files 5.3.1 Saving System image to a Net work Server 5.3.2 Replacing Sy stem image from a Network Server 5.4 Configuring SNMP 5.4.1 Configuring SNMP Support 5.5 Spanning Tree Algorithm 5.5.1 Spanning Tree Parameters 5.5.2 Rapid Spanning Tree Protocol (RSTP) 5.5.3 Configuring spanning-tree Page Page Page Chapter 6: Configuring IP 6.1 Establish Address Resolution 6.2 Managing IP Multicast Traffic 6.2.1 IGMP Overview 6.2.2 Configuring IGMP Page 6.3 Access Lists 6.3.1 Creating an Access List 6.3.2 Configuring an Access List Page 6.3.3 Applying an Access List to an Interface 6.3.4 Enabling an Access List Chapter 7: VLAN Configuration 7.1 Creating or Modifying a VLAN 7.2 VLAN Port Membership 7.2.1 configuring vlan ports 7.2.2 Trunk (IEEE 802.1q) Page Chapter 8: Quality of Service Configuration 8.1 Scheduling algorithm 8.1.1 Configuring Weighted Round Robin 8.1.2 Monitoring Weighted Round Ro bin 8.2 Priority Queuing 8.2.1 Priority Mapping 8.2.2 Port Based QOS 8.2.3 802.1P Based QOS 8.2.4 IP Based QOS 8.3 Traffic Shaping 8.3.1 Configuring Traffic Shaping for an Interface 8.4 Rate Limiting Chapter 9: Configuring the Switch Using the GUI 9.1 Main Configuration Menu 9.2 System 9.2.1 System System Information 9.2.2 System Network management Page 9.2.3 System Time Setting Page Page Port management LACP Property Port Management LACP Property Port. Port Management LAG Group. Port Management LAG Group - Each Group. 9.4 VLAN Management. Page VLAN MANAGEMENT VLAN PORT. 9.5 Spanning Tree Page Page Page 9.6 Multicast. Static multicast settings can be set. Port by port participation can be controlled. IGMP 9.7 Security - Port Security. Each port can be listed individually or a table can be displ ayed using the Show Table button Page TACAS+ and Storm Control are available on the next screens. Page Page DSCP 802.1P Port-based QoS Rate Control 9.9 SNMP SNMP Continued Page Page Page Page Page Page ADMIN Continued Page Page Page Page DHCP Relay/ DCP Option 82 these screens control the relay of DHCP information from a server. Page Page Page Page 9.13 Help General help is available for many screens. Page Chapter 10: CLI Commands 10.1 Modes 10.2 User Mode commands 10.3 Privileged Mode commands Page Page Page Page Page Page 10.4 Global Config mode commands Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 10.5 Interface Config mode commands Page Page Page Page Appendix A: Basic Troubleshooting Appendix B: Specifications TECHNICAL SPECIFICATIONS Interfaces Status Indicators Performance Specifications Page Standards Compliance L2+ Management Specification s Network Standards Physical Environmental Specifications System Requirements Modules Security Package Content Warranty Asante Service Appendix C: FCC Compliance and Warranty Statements C.1 FCC Compliance Statement C.2 Important Safety Instructions Page Index