Asus AT5NM10T-I

ASUS AT5NM10-I 1-14

4. Chassis intrusion connector (4-1 pin CHASSIS)

This connector is for a chassis-mounted intrusion detection sensor or switch. Connect

one end of the chassis intrusion sensor or switch cable to this connector. The chassis

intrusion sensor or switch sends a high-level signal to this connector when a chassis

component is removed or replaced. The signal is then generated as a chassis intrusion

event.

By default, the pin labeled “Chassis Signal” and “Ground” are shorted with a jumper

cap. Remove the jumper caps only when you intend to use the chassis intrusion

detection feature.

5. Internal speaker connector (4-pin SPEAKER)

The 4-pin connector is for the chassis-mounted system warning speaker. The speaker

allows you to hear system beeps and warnings.

E5179_AT5NM10-I.indb 14 12/22/09 5:56:02 PM

Contents

Main E5179 First Edition V1 December 2009 Contents Chapter 1: Product introduction Chapter 2: BIOS information Page Notices Federal Communications Commission Statement Canadian Department of Communications Statement REACH Safety information Electrical safety Operation safety About this guide How this guide is organized Conventions used in this guide Where to nd more information Italics Typography Bold text Page AT5NM10-I specications summary Chapter 1 Product introduction 1.1 Before you proceed 1.2.2 Layout contents 1.2 Motherboard overview 1.2.1 Motherboard layout Page 1.4.2 Memory congurations You may install 512MB, 1GB, and 2GB unbuffered non-ECC DDR2 DIMMs into the DIMM sockets. AT5NM10-I Motherboard Qualied Vendors Lists (QVL) DDR2-667 MHz capability 1-5 Chapter 1: Product introduction DDR2-667 MHz capability ASUS AT5NM10-I 1-6 Vendor Part No. Size SS/ DS E5179_AT5NM10-I.indb 6 12/22/09 5:55:50 PM Chip Brand Chip NO. Timing Voltage DIMM support A* B* 1-7 Chapter 1: Product introduction Visit the ASUS website at www.asus.com for the latest QVL. E5179_AT5NM10-I.indb 7 12/22/09 5:55:52 PM Vendor Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage 1.5 Expansion slot 1.5.1 Installing an expansion card 1.5.2 Conguring an expansion card 1.5.3 PCI slot 1.6 Jumpers AT5NM10-I Keyboard Power Setting PS2_USBPW1-4 1.7 Connectors 1.7.1 Rear panel connectors 1.7.2 Internal connectors Page Page Page Page AT5NM10-I Digital audio connector 1.8 Software support 1.8.1 Installing an operating system 1.8.2 Support DVD information To run the Support DVD Chapter 2 BIOS information Updating the BIOS 2.1.1 ASUS Update utility Installing ASUS Update 2.1.2 ASUS EZ Flash 2 2.1.3 ASUS CrashFree BIOS Recovering the BIOS 2.3 Main menu 2.2 BIOS setup program Entering BIOS Setup at startup Entering BIOS Setup after POST 2.3.1 System Time [xx:xx:xx] 2.3.2 System Date [Day xx/xx/xxxx] 2.3.3 SATA 1/2 2.4 Advanced menu 2.3.4 Storage Conguration Congure SATA as [IDE] SATA Run Mode Conguration [Compatible] 2.3.5 System Information 2.4.1 CPU Conguration 2.4.2 Chipset 2.4.3 Onboard Devices Conguration 2.4.4 USB Conguration USB Functions [Enabled] USB 2.0 Controller [Enabled] Legacy USB Support [Auto] USB 2.0 Controller Mode [HiSpeed] 2.5 Power menu 2.4.5 PCI PnP 2.5.1 Suspend Mode [S3 Only] 2.5.2 ACPI 2.0 Support [Enabled] 2.5.3 ACPI APIC Support [Enabled] 2.5.4 APM Conguration 2.5.5 Hardware Monitor 2.6 Boot menu 2.6.1 Boot Device Priority 1st ~ xxth Boot Device 2.6.2 Boot Settings Conguration Quick Boot [Enabled] 2.6.3 Security Change Supervisor Password User Access Level [Full Access] Change User Password Clear User Password Password Check [Setup] 2.7 Tools menu 2.7.1 ASUS EZ Flash 2 2.7.2 Express Gate [Auto] ASUS AT5NM10-I 2-16 2.7.3 AI NET 2 2.8 Exit menu