Manuals / Brands / Computer Equipment / Switch / Asus / Computer Equipment / Switch

Asus E1816 Apply, Config, Reload, Figure 4.18.1 Physical Interface (GigaX 1024I), GigaX Smart Switch Centralized Network Management

1 44

Download 44 pages, 2.5 Mb

Figure 4.18.1 Physical Interface (GigaX 1024I)

Above shows the configuration for each port. Select the ports you want to configure or reload information from the switch by clicking on the check boxes in front of the ports, then click on Config to set the configuration for the ports, or click on Reload to retrieve configuration from the switch, or click on Apply to apply the new settings to the switch. Some settings you can do to the physical interface.

1.Enable or disable a port

2.Speed and duplex mode. Select 1000 full-duplex (GigaX 1024P only) on the Fast Ethernet ports (from 1 to 24) will set the ports to 100 full-duplex mode.

3.Flow control - Back pressure flow control is used in half and full duplex modes to prevent packet loss.

A software reset will be triggered after the configuration is apply. The purpose of software reset is to restart link negotiations.

GigaX Smart Switch Centralized Network Management

Contents

E1816 / Oct Copyright Information Limitation of Liability Product Contact Information ASUSTeK COMPUTER INC. (Asia-Pacific) Technical Support ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Germany & Austria) Table of Contents Copyright Information Product Contact Information 1 Introduction 2 Getting to Know the GigaX Smart Switch 1 Introduction 1.2 Using this Document 1.2.1 Notational conventions 2.1 Parts List 2.2 GigaX Smart Switch Features 2.3 Technical Specifications Physical Dimensions: Environmental Ranges 2.4 Front Panel 2.5 Rear Panel 3 Quick Start Guide 3.1 Part 1 — Connecting the Hardware 3.1.1 Installing the Switch on a Flat Surface 3.1.2 Mounting the Switch in a Rack 3.2 Part 2 —Startthe Switch 3.2.1 Step 1. Connect to the PC with CNM Installed 3.2.2 Step 2. Connect to computers or a LAN 3.2.3 Step 3. Attach the power cord LED Indicators 3.3 Management from CNM 3.3.1 Switch Discovery and Management Page Discovery Figure 3.3 Available Switches (GigaX 1024P) Figure 3.3.1 Available Switches (GigaX 1024I) 3.3.2 Password Recovery 3.3.3 Factory Default Setting 4 Management Functions 4.1 Start CNM Program 4.2 Functional Layout Figure 4.3 A Topology Frame Figure 4.4 Tree view of the network topology 4.3 General Settings for CNM 4.3.1 Topology Add Switch Figure 4.6 Add Switch (GigaX 1024P) Figure 4.6.1 Add Switch (GigaX 1024I) 4.3.2 Setup 4.4 Switch Topology 4.4.1 Topology Discovery 4.4.2 Switch Add and Removal 4.4.3 Topology Load and Save 4.5 Switch Setup 4.6 System 4.6.1 Reboot 4.6.2 Link Status Reload 4.6.3 Change Password 4.6.4 Load 4.6.5 Save 4.6.6 Apply and Save 4.7 Configuration 4.7.1 Physical Interface Figure 4.18.1 Physical Interface (GigaX 1024I) Config Reload 4.7.2 Link Aggregation Trunking Status 4.7.3 Bandwidth Page 4.7.4 Traffic Control 4.7.5 VLAN Setup Page Control Option Figure 4.22 VLAN Control Options 4.7.6 IGMP Snooping 4.7.7 QoS Setup Page 4.8 Statistics 4.8.1 Port Traffic Setup Draw Traffic Chart 4.8.2 Traffic History 4.8.3 Comparison