Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus K7V 9)Floppy Disk Drive Connector (34-1pinFLOPPY), 8)Primary (Blue) / Secondary IDE Connectors (Two 40-1pinIDE)

1 110

Download 110 pages, 4.44 Mb

.3

3.HARDWARE SETUP

8)Primary (Blue) / Secondary IDE Connectors (Two 40-1pin IDE)

These connectors support the provided UltraDMA/66 IDE hard disk ribbon cable. Connect the cable’s blue connector to the motherboard’s primary (recommended) or secondary IDE connector, and then connect the gray connector to your UltraDMA/66 slave device (hard disk drive) and the black connector to your UltraDMA/66 master device. It is recommended that non-UltraDMA/66 devices be connected to the secondary IDE connector. If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accord- ingly. Please refer to your hard disk documentation for the jumper settings. BIOS now supports specific device bootup (see 4.4.1 Advanced CMOS Setup). (Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged).

TIP: You may configure two hard disks to be both Masters with two ribbon cables – one for the primary IDE connector and another for the secondary IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through 4.4.1 Advanced CMOS Setup.

IMPORTANT: UltraDMA/66 IDE devices must use a 40-pin 80-conductor IDE cable for 66MBytes/s transfer rates.

H/WConnectors

SETUP

K7V

K7V IDE Connectors

Primary IDE Connector						Secondary IDE Connector






		PIN 1

NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1.

9)Floppy Disk Drive Connector (34-1pin FLOPPY)

This connector supports the provided floppy drive ribbon cable. After connect- ing the single end to the board, connect the two plugs on the other end to the floppy drives. (Pin 5 is removed to prevent inserting in the wrong orienta- tion when using ribbon cables with pin 5 plugged).

FLOPPY

NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.

K7V

PIN 1

K7V Floppy Disk Drive Connector

38	ASUS K7V User’s Manual

Contents

Page Product Name: K7V Manual Revision: 1.01 E533 Release Date: April ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Technical Support ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) 2.1.3 Intelligence (only with optional hardware monitor) 3.5.2 DIMM Memory Installation 3.6.1 Quick CPU Installation Procedure 3.6.3 Installing the Universal Retention Mechanism 3.6.7 Recommended Heatsinks for Slot A Processors 5.5 AUDIO Driver (only with onboard audio option) 5.10 ASUS PC Probe x YAMAHA XGStudio (only with onboard audio option) Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver •Consult the dealer or an experienced radio/TV technician for help 1.1How This Manual Is Organized 1.2 Item Checklist 1.2.1 Motherboard 2.1The ASUS K7V Motherboard 2.1.1 Specifications 2.1.1.1 Optional Components 2.1.2Performance Intelligence 2.2K7V Motherboard Components K7V Motherboard Component Locations 3.1K7V Motherboard Layout 3.2Layout Contents SETUP H/W 3.3Hardware Setup Procedure 3.4Motherboard Settings 1)JumperFree™ Mode (JEN) 4.4 Advanced Menu 6) Voltage Regulator Output Setting Setting JEN 3)Onboard Audio Setting (available on audio model only) AUDIO CODEC Enable [1-2] [1-2] [1-2] [1-2](default) Disable 5)CPU External Frequency Setting (DSW) 2.In JumperFree mode, all dip switches (DSW-1–DSW-4)must be set to OFF When JumperFree mode is enabled, use BIOS setup in place of these switches (set Operating Frequency Setting User Define External Frequency Table (MHz) TACT INFORMATION) 6)Voltage Regulator Output Setting (VID1, VID2, VID3) 3.5System Memory (DIMM) 3.5.1 General DIMM Notes 3.5.2DIMM Memory Installation Page 3.6.1 Quick CPU Installation Procedure 3.6.2Attaching the Heatsink 3.6.3 Installing the Universal Retention Mechanism 3.6.4 Installing the Processor 3.6.5 Removing the Processor 3.6.6Smart Thermal Solutions 3.6.7 Recommended Heatsinks for Slot A Processors 3.7Expansion Cards 3.7.1 Expansion Card Installation Procedure 3.7.2 Assigning IRQs for Expansion Cards Standard Interrupt Assignments Interrupt Request Table for this Motherboard 3.7.3Accelerated Graphics Port Pro (AGP Pro) 3.7.4 Audio Modem Riser (AMR) Slot Page 3.8External Connectors 4)Parallel Port Connector (Burgundy 25-pinPRINTER) Onboard Parallel Port 4.4.2 I/O Device Configuration) NOTE: Serial printers must be connected to the serial port NOTE 6)Joystick/MIDI Connector (Gold 15-pinGAME_AUDIO) (optional) 7)Audio Port Connectors (Three 1/8” GAME_AUDIO) (optional) 8)Primary (Blue) / Secondary IDE Connectors (Two 40-1pinIDE) 9)Floppy Disk Drive Connector (34-1pinFLOPPY) 10)Wake-On-LANConnector (3-pinWOL_CON) Wake-On-Lan 4.4.3 Power Management 11)Wake-On-RingConnector (2-pinWOR) 12)IDE Activity LED (2-pinIDELED) do not place jumper caps over these pins 14)Internal Audio Connectors (4-pinCD, AUX, VIDEO, MODEM) Headphone True-Level Line Out Header (3 pin HPHONE) (optional) 16)Serial Infrared Module Connector (5-pinIR) 17)SMBus Connector (5-1pin SMB) 18)Chassis Intrusion Lead (2-pinCHASSIS) 19)ATX Power Supply Connector (20-pinblock ATXPWR) 20)USB Connector Set (10-1pin USBPORT) 21)Digital Audio Interface Connector (3-pinSPDIFOUT) (optional) The following is for items 22–27(next page) K7V System Panel Connectors 22)System Warning Speaker Connector (4-pinSPEAKER) 23)System Power LED Lead (3-1pin PWRLED) 24)System Message LED Lead (2-pinMSG.LED) 25)Reset Switch Lead (2-pinRESET) 26)ATX Power Switch Lead (2-pinPWRSW) 3.9Starting Up the First Time Award BIOS Beep Codes 4. BIOS SETUP Powering Off your computer: Start Shut Down Shut down the computer 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 4.1.2 Updating BIOS Procedures 6.When prompted to confirm the BIOS update, press Y to start the update Flashed Successfully 8. Follow the onscreen instructions to continue Page 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Translation Method [LBA] Cylinders Translation Method Head Sector CHS Capacity Maximum LBA Capacity Multi-SectorTransfers [Maximum] 4.3.2 Keyboard Features Language [English] A Note about Passwords Forgot the Password Halt On [All Errors] Installed Memory [XXX MB] 4.4Advanced Menu CPU Vcore Setting [Auto] CPU Vcore CPU Vcore CPU Level 1 Cache, CPU Level 2 Cache [Enabled] CPU Level 2 Cache ECC Check [Disabled] Notes for JumperFree Mode 4.4.1Chip Configuration SDRAM CAS Latency SDRAM Configuration SDRAM RAS Precharge Time SDRAM RAS to CAS Delay Delayed Transaction [Enabled] 4.4.2I/O Device Configuration Onboard Peripheral Resource Control For motherboards without onboard PCI audio chipset 4.4.3PCI Configuration PCI/PNP IRQ Resource Exclusion PCI/PNP DMA Resource Exclusion PCI/PNP UMB Resource Exclusion 4.4.4 Shadow Configuration 4.5Power Menu Video Off Option [Suspend ->Off ] Video Off Method [DPMS OFF] HDD Power Down [Disabled] Suspend-to-RAMCapability [Disabled] Suspend Mode [Disabled] 4.5.1Power Up Control Automatic Power Up [Disabled] 4.5.2Hardware Monitor 4.6Boot Menu Boot Sequence Plug & Play O/S [No] Reset Configuration Data [No] Boot Virus Detection [Enabled] Quick Power On Self Test [Enabled] Boot Up Floppy Seek [Disabled] 4.7Exit Menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5.1Operating Systems 5.1.1 Windows 98 First Time Installation 5.2K7V Series Motherboard Support CD 5.2.1 Installation Menu 5.3Registry patch for VIA Chipset 5.4VIA PCI IRQ Routing Miniport Driver AUDIO Driver 5.6PC-cillin98 5.7Acrobat Reader 5.8IDE Driver 5.9 AGP Miniport Driver 5 . 1 0 ASUS PC Probe YAMAHA XGStudio 5.12Uninstalling Programs 6.1ASUS PC Probe 6.1.1 Starting ASUS PC Probe 6.1.2Using ASUS PC Probe Settings History Fan Control Information Hard Drives Memory Shows the PC’s memory load, memory usage, and paging file usage Device Summary Shows a summary of devices in your PC DMI Explorer 6.1.3ASUS PC Probe Task Bar Icon 6.2YAMAHA XGStudio 6.3.1 Using YAMAHA XGplayer 6.3.2 YAMAHA XGplayer Main Panel 6.3.3YAMAHA XGplayer Mixer Panel 6.3.4 YAMAHA XGplayer Minimize Panel 6.3.5Troubleshooting Cannot install Does not start No sound 7.1PCI-L101Fast Ethernet Card 7.1.1 Features 7.1.2 Software Driver Support 7.1.3 Question and Answer 7.2 Modem Riser 7.2.1 56K Software Modem 7.2.2 Primary/Seconday MR Layout of Primary MR 7.2.3Hardware Installation Procedure 7.2.4Software Setup in Windows 7.3 Glossary Boot Bus Master IDE Byte (Binary Term) COM Port Concurrent PCI LPT Port (Line Printer Port) MMX (Klamath) CPU as well as other OnNow PC100 ROM (Read Only Memory) SCSI (Small Computer System Interface) SDRAM (Synchronous DRAM) SPD for SDRAM module SSE (Streaming SIMD Extensions)