Asus P2B-DS manual

P2B-D / P2B-DS

Dual Pentium® II Motherboards

USER’S MANUAL

Special Features

•P2B-DS

•Adaptec 7890 SCSI Chipset

•Adaptec 3860 SCSI Transceiver

Contents

Special Features Product Name: ASUS P2B-D/P2B-DS Manual Revision: 1.03 E253 Release Date: ASUSTeK COMPUTER INC Marketing Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH I. INTRODUCTION II. FEATURES III. INSTALLATION IV. BIOS SOFTWARE V. SUPPORT SOFTWARE VI. DESKTOP MANAGEMENT VII. ASUS LAN Card VIII. ADAPTEC SCSI SELECT IX. ADAPTEC EZ-SCSI Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver •Consult the dealer or an experienced radio/TV technician for help How this Manual is Organized This manual is divided into the following sections: Introduction Features Information and specifications FEATURES Specifications D/P2B The ASUS P2B-D/P2B-DSMotherboard Motherboard Parts II. FEATURES ASUS P2B-D/P2B-DSMotherboard Layout Layout Jumpers Expansion Slots/Sockets Hardware Monitor Connectors INSTALLATION Installation Steps Before using your computer, you must complete the following steps: 1.Set Jumpers on the Motherboard 2.Install System Memory Modules 3.Install the Central Processing Unit (CPU) Jumper Settings 3.CPU Bus Frequency (FS0, FS1, FS2) 4.CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) Internal External CPU Bus Frequency 5.Chassis Intrusion Sensor Setting (JP18) (optional/reserved) (This page was intentionally left blank.) 2.System Memory (DIMM) 3.3Volt SDRAM Configuration IMPORTANT (see General DIMM Notes below) (see DIMM Memory Installation Procedures Pentium II Processor Installing the Pentium II Processor Insert the Attach Mount Screws: Mount the Heatsink: Secure the SEC Cartridge: Recommended Heatsinks AAVID Heatsink Elan Vital Heatsink Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor Accelerated Graphics Port Connectors 5.External Connectors 1.PS/2 Keyboard Connector (6-pinFemale) 2.PS/2 Mouse Connector (6-pinFemale) 3.Parallel Printer Connector (25-pinFemale) NOTE 4.Serial Port COM1 and COM2 Connectors (Two 9-pinMale) 5.Floppy Disk Drive Connector (34-1pinFLOPPY) 7.Primary / Secondary IDE connectors (Two 40-1pinIDE) 8.Hard Disk Activity LED (2-pinIDELED) 9.Chassis, CPU, & Power Supply Fan Connectors (3-pinFAN) do not place jumper caps over these pins 10.IrDA-Compliantinfrared module connector (5-pinIR) 11.ATX Power Supply Connector (20-pinATXPWR) 12.Wake-On-LAN (3-pinWOL) Power Up Con- trol IV. BIOS SOFT- WARE 13.Chassis Intrusion Sensor Lead (CHASSIS) (optional/reserved) 14.LED Lead (MSG.LED) 15.SMI Suspend Switch Lead (SMI) 16.ATX Power Switch / Soft Power Switch (PWR_SW) 17.Reset Switch Lead (RESET) 18.System Power LED (PWR_LED) 21.Fast (50 pins)/Wide (68 pins)/Ultra2 (68 pins) SCSI Connectors 22.SB-Link™Connector (6-1pin DMA_HEADER) (optional/reserved) 23.SMBus Connector (3-pinSMB) (optional/reserved) Power Connection Procedures Main Menu 2. Update BIOS Including Boot Block and ESCD Flash Memory Writer IV. BIOS Managing and Updating Your Motherboard’s BIOS Upon First Use of the Computer System 2.Copy AFLASH.EXE to the just created boot disk Run AFLASH.EXE from this new disk and select option 1. Save Current BIOS to File 6. BIOS Setup BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup Time (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59) Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup Auto detection of hard disks on bootup Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled Video (EGA/VGA) BIOS Features Setup Details of BIOS Features Setup BIOS CPU Level 1 Cache / CPU Level 2 Cache (Enabled) CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache BIOS Update (Enabled) Security Option (System) Supervisor Password User Password System Setup Chipset Features Setup Details of Chipset Features Setup Graphics Aperture Size (64MB) Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Memory Hole At 15M–16M(Disabled) Onboard FDC Swap A & B (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Power Management Setup Details of Power Management Setup Video Off Method (DPMS OFF) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Disabled Wake On LAN (Enabled) Automatic Power Up (Disabled) PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) Onboard AHA BIOS (Auto) ONB AHA BIOS First (No) ONB SCSI SE Term. (Enabled) Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save & Exit Setup Exit Without Saving S/W SUPPORT ASUS Smart Motherboard Support CD ASUS PC Probe Utility: NOTE: This utility will not run with LDCM installed LDCM Local Setup: •PC-cillinLite:Installs PC-cillinLite, a virus scanning software package Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes Save MIFD Load MIFD Load BIOS Defaults Page ASUS PCI-L101Fast Ethernet Card Software Driver Support Question and Answer SCSI Disk Utilities Page Windows95 or WindowsNT Windows/Windows for Workgroups DOS SCSI Device Troubleshooting Windows95/WindowsNT Troubleshooting Place the Windows95 3Click on the Have Disk button, then click the Browse button What do I need to do if I want to use another host adapter Open the Control Panel Double-click If I am running under Windows95, do I need lines for the Adaptec real mode CONFIG.SYS AUTOEXEC.BAT •You are running in MSDOS mode You are using a scanner or another SCSI device with CONFIG.SYS- or DOS and Windows3.1x Device Drivers DOS and Windows3.1x ASPI Managers DOS Formatting Utilities Low-levelFormatter (scsifmt) Formatter and Partitioner (afdisk) 7.To quit afdisk, press Esc and select Yes to confirm that you want to quit