AT&T 7650 Play All Messages Record a Memo, Connect with Answering System, Save Messages, Repeat

...ANSWERING SYSTEM OPERATION...

Answering System Operation fr'omCordless Handset or Remote Touch Tone Phone

You can operate the answering system from the cordless handset, or from any touch tone phone away from your home

or office. The labels above the number
I . ..1 - .		i:.i	. .	. ? ,
":a	..\. ,&., v i r		. U L ; ! ~ ~ >;ICLLICI>CL	' i k i l l

Play All Messages		Record a Memo
Press and release pr.	1	Press ANSSYSTEM,.
	2 Press :.--
	?	Ert-rm?i!hcx xo:'.?r ( I or 7). Th:

remind you of the correct buttons to press for each operation.

Connect with the

Answering System

(from the cordless handset)

1Press i ANS SYSTEM:.

The ANS S Y m light goes on.

2The system announces whether or

not you have messages, then beeps twiceandisrea~d2acceptacomrnand

3Press 7or a . The system now prompts you to select a mailbox.

(trom a remote touch tone phone)

1Dial your telephone number.

2When your answering system responds, enter your ,-digit Remote Access Code. The systemannounces whether or not you have any messages, then beeps twice and is

ready to acce t a command.

,,

3 Press a or &m . The system now prompts you to select a mailbox.

NOTE: If you do nor enter a command or select a mailbox, the system plays back all messages in both maiboxes.

Remote Access Code

The Remote Access Code is a 2-digit security code which lets you access your answering system remotely. The factory setting is 50, but you can change this number.

To change remote access code

1Press c,au U,m;am after the two beeps.

2Enter a new code between 50 and 99.

3If the entry is valid, the system an- nounces your code, followed by two beeps. If the entry is invalid, you will hear a 5-beep signal.

Save Messages

The system automatically saves messages after playback.

Delete Messages

To delete all messages in a particular

DELT3

mailbox, press , then the desired mailbox number (1 or 2).

Repeat

Press and release 3.The system now plays the current message from the be- ginning. To go to thezprevious. message, press and release

Forward

Press and release FORWIROiz while the system is playing a message to advance to the

next messa e. Each time you press and

-3

release 3 the system advances to the next message.

Stop

Press 6- while the system is playing a message. The system stops playing, beeps twice, and is ready to accept a command.

Outgoing Announcement

To record an announcement

C K u G a*HHC .

Press $, iJThe system beeps and then begins recording.

Press /$ when you are done. If you pause for more than 7 seconds, the system will stop recording. The system beeps and replays the announcement.

review announcement

Press after the 2-beep signal.

system beeps.

4Begin recording your message.

5When you are finished, press or

-on the cordless handset,-OFF

hang up if you are on a remote touch tone phone.

Clock

To review timdday setting

Press and release 3.The system announces the current dayhime setting. and beeps twice to indicate it is ready to accept a command.

To change timdday &fin&

Press and release , a.The sys- tem announcesthe current day setting. To set day, press and releg:

to move a day earlier, or fi to move a day later. When you hear the correct day, go on to set the hour. To set the hour, press and release 3.The system announces the an- rent hour setting. Press and release

aw_r	or	fawm
, 4		a to move the hour up or

dywn. When you hear the correct hour setting,go on to set minutes. To set minutes, press and release

arx

3.The system announces the cur- rent minute setting. Press and release

-
-1
.T or	to move the setting up

or down. When you hearnthe. correct minute setting, press The system announces the new t i m a y setting, and beeps twice to show it is ready for another command

Room Monltor

You can call the system from any remote touch tone phone and listen to activity in the room. Press 3 to listen for 30 seconds. For another 30 seconds, press I Z again.

To review remote access code

Press 5 after the two beeps. The system announces your code, followed by two beeps.

Record a Memo

Press IANSSYSTEM?.

Press ;+MEMOD w a y ; .

3Enter mailbox number (1 or 2). The system beeps.