Atlas Sound CP400 user service Rear Panel Description

CP400 & CP700 COMMERCIAL POWER AMPLIFIER

OWNER'S MANUAL

4. Limit LED Indicator

The CP400 and CP700 come equipped with limiter circuitry and LEDs to indicate when this circuitry is activated. The limiter circuitry engages only when the input signals reach a specific, factory set magnitude. Once this limit has been reached, the circuitry will reduce the input level enough to prevent clipping at the speaker output terminals.

rear Panel Description

10			CH-18, 4, and 2 Ohms			AUDIO TRANSFORMER CH-1
	CP700		D I R . O U T P U T +		-	0	70		100 I S O L . O U T P U T
	Commercial
	Power
	Amplifier
	Per Channel
	Output Power	+				-	+	-	+
	400 W / 4 Ohms			BRIDGE		70V			25V
						-	100V		+
	350 W / 70.7 V			MONO
			CH-2 8, 4, and 2 Ohms			AUDIO TRANSFORMER CH-2
			D I R . O U T P U T +		-	0	70		100 I S O L . O U T P U T
	AC100V-50/60Hz
	AC120V-50/60Hz
	AC230V-50/60Hz
	AC240V-50/60Hz
			-			-	+	-	+
						70V			25V
				BRIDGE
				MONO		-	100V		+
	POWER
										MADE IN CHINA
		CAUTION							CAUTION
								RISK OF ELECTRIC SHOCK
	TO REDUCE THE RISK OF ELECTRIC SHOCK								DO NOT OPEN
								AVIS RISQUE DE CHOC ELECTRIQUE
	DO NOT REMOVE COVER (OR BACK)
	NO USER SERVICEABLE PARTS INSIDE									NE PAS OUVRIR
	REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

11

6

IN															IN
						AMPLIFIER INPUTS
							CH-2	CH-1
							+ - GND	- +
THRU			22	18	16	1				22	18	16	1		THRU
		6				41			6				41
2	2					1		2	2				1
							0							0
3							8	3						8
0								0
4							6	4						6
6							4	6						4
5						0	2	5					0	2
		0							0
GND			0-	LEVEL						0-	LEVEL
										STEREO
								PARALLEL						BRIDGE

1601 Jack McKay Blvd., Ennis, TX 75119

(800) 876-3333 AtlasSound.com

9

Figure 2

8

7

5

5. Gain Controls

One stepped attenuator per channel increases or decreases the sensitivity by 2 dB per step. Maximum voltage gain is 32 dB.

6. CH1/CH2 Inputs (XLR Connectors)

Two female XLR inputs (one per channel) are provided. These inputs are balanced and configured as follows: pin 1 ground, pin 2 +, pin 3 -. The XLR connections are typically used in portable audio systems where quick connect and disconnect is warranted.

7. Balanced Barrier Strip Inputs

Balanced inputs are provided on this barrier strip for permanent installation applications. The use of the appropriate spade type lug is highly recommended for best connection integrity and a neat, professional appearance.

8. CH1/CH2 Loop Through

Two male XLR (one per channel) are provided for looping the input signals to other devices. These connectors are wired in parallel with the female XLR inputs, pin for pin.

Specifications are subject to change without notice

AtlasSound.com

1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. •		TELEPHONE: (800) 876-3333 •	FAX: (800) 765-3435
©2008 ATLAS SOUND LP	Printed in U.S.A.	ATS002102 RevD 2/08	PP

5