TH146-P-U
Installation Guide
Programmable H/C Controller
Removable |
|
|
|
|
|
|
|
|
| Removable |
Connector * |
|
|
|
|
|
|
|
|
| Connector * |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Temperature Sensor | |
|
* To remove a connector from the control module, pry with a screwdriver.
1. Introduction
1.1 Applications
The
Heat pump | 1H1C, 2H1C, 2H2C, 3H1C, 3H2C, 3H3C, 4H2C | |
|
| |
HVAC | 1H, 2H, 3H, 1C, 2C, 3C, 1H1C, 1H2C, 2H1C, 2H2C, | |
2H3C, 3H1C, 3H2C, 3H3C | ||
| ||
|
|
The following devices can be connected to the controller:
air recirculation fan humidifier
dehumidifier or air exchanger
remote control device (for the unoccupied mode)
1.2 Supplied Parts
•
•
•
1.3 Accessories
•RC845 relay (see section 2.4)
•
•CT241 telephone controller (see section 2.10)
2. Installation
2.1 Control Module (CT280-3H3C)
Configure the control module according to your type of heating/cool- ing system using DIP switches on the back of the module.
Heat pump |
|
|
| HVAC | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Install the control module near the heating/cooling system, away from any heat source.
2.2 User Console (TH146-P)
Install the console in a central location. Avoid locations with air drafts (e.g., top of staircase or air outlet) or stagnant air (behind a door). Do not install the console on a wall hiding air ducts nor expose it to direct sunlight.
NOTE: If this controller replaces an old thermostat, any two of the wires that were connected to the thermostat can be used to connect the user console to the control module. The maximum wiring length is 30 m (100 ft).
5/24/07 | 1/12 |