VOH683 | exiting the pod |
| Note: cables |
| should be routed |
| as shown. |
| Red : +12 VDC |
| Pow er Harne ss | 12 Pin Power signal | ||||||
|
| Item # 4 |
|
| Harness Item #3 | |||||
| (A ccesso ry Cir. ) |
|
|
| ||||||
|
|
|
|
|
| c h ok e |
| |||
|
|
|
|
|
|
|
|
| ||
| Black: G rou n d |
|
|
|
|
|
|
|
| |
|
|
|
| Optional Hard W ired FM Modulator Output |
|
| ||||
| 12 VDC Power and Ground |
|
| RCA |
| |||||
|
|
| Left |
| ||||||
| A m /Fm |
|
|
|
|
|
| In put | L EFT | |
TO | A nte nn a |
|
| F M |
|
|
|
| ||
|
|
|
|
|
| WHITE | ||||
|
|
| M od ulato r |
|
| Patch Cord | ||||
FAC TO R Y |
|
|
|
|
| RIGHT | ||||
|
| 1 07 0 6 1 0 |
|
|
| RCA Male to Male | ||||
RA D IO | D as h R a dio |
|
|
|
| Right | R ED | |||
*Refer to Instructions with the RF |
| |||||||||
|
| |||||||||
|
| In put |
| |||||||
|
| Modulator Kit for further details. | RCA |
| ||||||
|
|
|
| To Secondary AV Monitor |
| |||||
TO | 12 VDC Power and Ground | IN PUT | RCA |
| ||||||
O P TIO N A L | VIDEO |
|
|
| ||||||
|
|
|
|
|
|
| LINE | |||
A D D IT IO N A L |
|
|
|
|
|
|
|
| ||
A ux illa ry |
|
|
|
|
| OUT | ||||
M O IN TO R |
|
|
|
| Patch Cord | |||||
| vide o d is pla y |
|
|
| VIDEO | |||||
|
|
|
|
| RCA M ale to Male |
|
2 1
Connect to FM radio antenna or equiv alent.
Ac cess ory Harnes s Item # 2
Red RCA (Audio Right)
White RCA (Audio Left)
Yellow R CA (Video)
Optional Remote H eadphone Stations |
|
Stereo | Green |
Hea dpho ne Jack | (Right+) |
Stereo | Black |
Hea dpho ne Jack | (Ground) |
| Gray |
| (Left+) |
IR LED :
Clean the IR R eceiver Window on the front of the V CP. Rem ove A dhesive Backing and Apply IR LED to IR Window on the Fac e of the V CP.
"Y " Adapter fo r use with
Figure A
1)Make the connections to the vehicle for the 12 pin wiring harness.
2)Remove screws on PCB Cover. Open the cover to gain access to
3)Insert the Circular
4)Pull the wire tie loop tight and cut off the excess.
5)Connect the 12 pin harness to the mating connector on the Video Monitor.
6)Connect the wired RF Modulator and / or the remote headphone jacks to the video monitor if those options are being included.
7)Connect power harness to vehicle’s electrical system by tapping into an accessory hot line.
8)Reinstall PCB cover using the 2 screws.
9)Connect FM radio antenna to the existing vehicle antenna or equivalent using the supplied 144" Adapter Cable and the "Y" Adapter (Refer to Figure C.)
10)Verify all functions of the System before final mounting of the finished assembly.
Note: A second VCP or other A/V Component can be connected to the video monitor system using a
second source component harness (purchased separately, part number: 8010730). This second har- ness would plug into the second
A/V Source Definitions:
1= VCP (Right
2= 2nd VCP (or game or DVD, etc.…. left