Manuals / Avaya / Computer Equipment / Switch

Avaya P120 SMON manual The Port Statistics Window, 4. LAG Information Box

Models: P120 SMON

1 71

Download 71 pages 22.98 Kb

Page 30

The Port Statistics Window

Chapter 4

The Port Statistics Window

The Port Statistics window is organized as follows:

•The title of the Port Statistics window shows the IP address of the device.

•The X axis represents packets or percentage for Utilization.

•The Y axis represents ports and LAGs. Each row on the graph corresponding to a port or LAG is labeled on the Y axis with a port number, LAG number, or with the user defined name for a port.

•Link Aggregation Groups (LAGs) are displayed. These are a group of ports serving as one logical link. When referencing the LAG’s information box (place your cursor over the LAG bar), each port within the LAG appears. In addition, the speed of the LAG is the sum of the speed of all the ports within the LAG.

Figure 4-4. LAG Information Box

*Note: For high-speed ports with large polling intervals, bandwidth and utilization counters may be inaccurate.

For more information about modifying the display, and the available toolbar, status bar, and mouse movement options, refer to Chapter 2, Working with Device SMON Tools.

23	Avaya P120 SMON User Guide

Image 30

Avaya P120 SMON manual The Port Statistics Window, 4. LAG Information Box

Contents

Avaya P120 SMON User Guide AprilAvaya P120 SMON User Guide Copyright 2002 Avaya Inc. All Rights ReservedChapter 1 - SMON Overview Chapter 3 - Switch StatisticsPreface Chapter 2 - Device SMONChapter 6 - Alarms and Events Chapter 4 - Port StatisticsChapter 5 - VLAN Statistics Appendix B - Setting Up the SMON License Appendix A - SMON Dialog BoxesIndex The Purpose of this Guide Avaya MultiService SMON User GuidePreface Table 1. SMON DocumentationWho Should Use this Guide Organization of this GuideWhat is RMON 1 SMON OverviewWhat is SMON Overview of SMONSMON Devices Filtering OptionsSpecific Filtering TopN Filtering Switch Statistics Overview Device SMON ToolsPort Statistics Overview VLAN Statistics OverviewAlarms and Events Overview Figure 1-1. Events OverviewThe first Event is a Rising Event, caused by the counter rate rising above the Rising Threshold. The second Event is a Falling Event, caused by the counter rate falling below the Falling Threshold. The third Event is a Rising Event. Note, that although the rate falls below the Rising Threshold and then rises above it again, no Event is generated. A new Rising Event can only be generated after the rate falls below the Falling Threshold. Similarly, after the fourth Event, although the rate rises above the Falling Threshold and then falls below it again, no Event is generated. A new Falling Event can only be generated after the rate rises above the Rising Threshold Accessing Device SMON 2 Device SMONThe Device SMON User Interface Figure 2-1. Avaya P120 SMON User InterfaceApplication Tabs Device SMON ToolbarTable 2-1. Toolbar Buttons to Appendix A, Using the Define VLAN Table 2-1. Toolbar Buttons Continuedto Appendix A, Using the Define Port Filter Dialog BoxStatus Bar Dialog AreaDesktop Table 2-2. Status Bar ItemsWorking with Device SMON Tools Status LineTable 2-3. Status Line Items Using Dialog Box Options Mouse ActionsTable 2-4. Mouse Actions Generating Reports Report Now Auto Report3 Switch Statistics Using Switch StatisticsFigure 3-1. Switch Statistics Window Gauges and Pie Charts in the Switch Statistics Window Table 3-1. Gauge Variables in Switch StatisticsTable 3-2. Pie Chart Variables in Switch Statistics Traffic Graph in the Switch Statistics Window Table 3-3. Traffic Variables in Switch StatisticsComparing the traffic graphs to the meters can often point you in the right direction for locating a problem. For example, the pie chart may show an abnormal amount of non-unicast packets, while the bandwidth usage shown in the traffic graph has increased significantly. This may suggest that one of the stations attached to the switch is generating the non-unicast packets. By using VLAN Statistics you can locate the VLAN where the problem originates. By using Port Statistics you can locate the port to which the suspected station is attached Using Port Statistics 4 Port StatisticsSelecting Ports to Display Port Statistics Variables Figure 4-1. Port Statistics Window - PacketsTable 4-1. Port Statistics Variables - Packets Figure 4-3. Port Statistics Window- Utilization Figure 4-2. Port Statistics Window - BandWidthTable 4-2. Port Statistics Variables - BandWidth Table 4-3. Port Statistics Variables - UtilizationThe Port Statistics Window Figure 4-4. LAG Information BoxUsing VLAN Statistics 5 VLAN StatisticsFigure 5-1. VLAN Statistics Window - Packets Selecting VLANs to DisplayVLAN Statistics Variables Table 5-1. VLAN Statistics Variables - PacketsVLAN Statistics Window Figure 5-2. VLAN Statistics Window - BandwidthTable 5-2. VLAN Statistics Variables - Bandwidth 6 Alarms and Events Using Alarms and EventsFigure 6-1. Alarms Table Alarms TableAlarms Table Fields Table 6-1. Alarms Table Fieldsconfigure Alarms using the Table 6-1. Alarms Table Fields ContinuedNote The Alarms and Events tool can only Rate @ Interval method. To configureFigure 6-2. Alarm Tooltip TooltipsTable 6-2. Tooltip Fields Editing Alarms Table 6-2. Tooltip Fields ContinuedAlarm Wizard Overview of the Alarm WizardActivating the Alarm Wizard Alarm Wizard Screens Welcome to the Alarm WizardFigure 6-3. Alarm Wizard - Welcome Screen Figure 6-4. Alarm Wizard - Select Port Select PortFigure 6-5. Alarm Wizard - Select Interval and Counter Screen Select Interval and CounterFigure 6-6. Alarm Wizard - Set Thresholds Set ThresholdsFigure 6-7. Alarm Wizard - Descriptions Figure 6-8. Alarm Wizard - Set Event Set EventFigure 6-9. Alarm Wizard - Set Trap Community Set Trap CommunityDevice Event Log SummaryFigure 6-10. Summary Figure 6-11. Device Event Log Table 6-3. Event Description FieldsTable 6-4. Event Log Fields Using the General Options Dialog Box A SMON Dialog BoxesFigure A-1. General Options Dialog Box Polling Interval Display ModePolling Interval Display Mode Report Setting Report Setting Using the Report Now Dialog Box Using the Auto Report Dialog BoxFigure A-2. Report Now Dialog Box Figure A-3. Auto Report Dialog Box Using the Switch Options Dialog Box Figure A-4. Switch Options Dialog BoxSamples To Store Level IndicatorsSamples Per Screen Logarithmic DisplayUsing the Port/VLAN Options Dialog Box Items Per ScreenFigure A-5. Port/VLAN Options Dialog Box Using the Find Dialog Box Figure A-6. Find Dialog Box for PortsFinding a VLAN Finding a PortFinding a LAG Using the Define Port Filter Dialog Box Figure A-7. Define Port Filter Dialog BoxTo remove ports from the List of Selected Ports Using the Define VLAN Filter Dialog Box Figure A-8. Define VLAN Filter Dialog BoxTo remove VLANs from the List of Selected VLANs Using the Define TopN Filter Dialog Box Figure A-9. Define TopN Filter Dialog BoxUsing the Find Top5 Peaks Dialog Box Figure A-10. Find Top5 Peaks Dialog BoxUsing the Sort Dialog Box Figure A-11. Sort Dialog BoxLicense Setting Up the SMONAvaya MultiService SMON Manager User Guide SMON Embedded LicenseIndex Page