Operation and Settings
Projecting Image
3 Adjust the zoom ratio (screen size) (when zoom lens is in use)
You can adjust the focus using the AZoomB item of the Lens menu.
If setting for this projector is not completed, refer to the “Setting Menu” (A Page 30) upon turning on the power and configure the settings accordingly.
Once the basic settings are configured, this projector can be used by simply performing the following operation procedures.
PREPARATION:
●Remove the lens cap.
●Connect this projector to the computer. (A Page 19, 21)
●Connect the LAN cable. (A Page 22)
Main
Image
Setting
Convergence
Lens
Option
Network
host
|
|
| Logout |
Zoom | Focus | Shift |
|
w | + |
| U |
| _ | L | R |
T |
|
| |
|
|
| D |
1 Set this projector to the standby mode, and display the main menu
●Refer to “Turn on the main power” (A Page 23), and steps 4 to 6 of “Assigning an IP Address” (A Page 26).
●The [STANDBY/ON] indicator lights up in red.
2 Click the AONB button under the APowerB item of the main menu to project the image
●The power of this projector turns on, and formatting is done taking a few minutes. A gray image will be displayed during formatting.
The projected image appears once formatting ends.
●The [STANDBY/ON] indicator lights up in green.
To enlarge the screen size:
Press the AWB (Wide) end of AZoomB
To reduce the screen size:
Press the ATB (Tele) end of “Zoom”
NOTE:
●The screen size changes each time you click on the inner buttons (
/
). (Fine control)
The outer buttons (
/
) change the screen size when they are depressed. (Coarse control)
4 Adjust the position of the projection screen
You can adjust the focus using the AShiftB item of the Lens menu.
Main
Image
Setting
Convergence
Lens
Option
Network
|
|
|
|
|
|
|
|
|
|
|
|
| host | |||||
|
|
|
|
|
|
|
|
|
|
|
|
| user: root | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| Logout |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| Power |
|
|
|
|
|
|
|
| Latest Error |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
| ON |
|
| OFF | STANDBY |
|
| 00 |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
| Signal Status |
|
|
|
|
| Temperature |
|
| ||||||||
|
|
| DVI |
| Rate(Hz) | Pixel H | Pixel V | Link |
|
| Temp. 1 |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
| 1 | 60.00 | 2048 | 2400 | Dual |
|
| 36.0 deg.C |
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
| 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| Temp. 2 |
| |||||||
| 3 | 60.00 | 2048 | 2400 | Dual |
|
|
| ||||||||||
|
|
| 25.5 deg.C |
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
| 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To shift the image upward:
Press the AUB end of AShiftB
To shift the image downward:
Press the ADB end of AShiftB
To shift the image rightward:
Press the ARB end of AShiftB
To shift the image leftward:
Press the ALB end of AShiftB
Projector Usage
Lamp Time | 1035h24m | Reset |
NOTE:
●You can also turn on the power by pressing the [OPERATE I/B] button on the projector unit for more than one second.
●The image may flicker for a few seconds immediately after projection starts. This is not a malfunction.
●After the lamp lights up, it takes about 1 minute or longer for the brightness of the video image on the screen to stabilize.
NOTE:
●When a zoom lens is used, the adjustment range for lens shift is between 0% to 100% in the vertical direction, and between 0% to 50% in the horizontal direction (during
When a short focal length lens is used, the adjustment range for lens shift is between 0% to 30% in the vertical direction, and between 0% to 10% in the horizontal direction (during
●The position changes each time you click on the inner buttons (
/
). (Fine control)
The image shifts when the outer buttons (
/
) are depressed. (Coarse control)
●The lens shift feature does not function if the lens mechanism is secured. (A Page 14 ALens Fixation MechanismB)
28
