Setting Value Description Power, Latest Error, RateHz | Barco LX-5

LX-5_EN.book Page 31 Friday, July 4, 2008 9:35 AM

Item	Setting Value	Description
Power	ON	For turning the power ON/OFF.
	OFF	ON : Turns on the power.
		ON : Turns on the power.
		OFF : Turns off the power.

		NOTE:
		NOTE:
		● The following operating modes of the projector are displayed to the
		right of the OFF button.
		STANDBY				: Standby (OFF)
		PROJECTION				: Lamp Illuminated (ON)
		FAN ENABLE				: FAN Enable (OFF	ON)
		LAMP ENABLE				: LAMP Enable (OFF	ON)
		DEVICE ENABLE				: Elemental Device Enable (OFF ON)
		COOLING				: Cooling (OFF)
		EMERGENCY				: Error Occurred (Cooling not performed)
		EMERGENCY COOLING : Error Occurred (Cooling performed)
		● When in the standby mode, clicking the ON button each time
		switches the mode in the sequence of STANDBY DEVICE
		ENABLE			LAMP ENABLE FAN ENABLE PROJECTION.
		● Clicking the OFF button when the power is on switches the projector
		to the cooling mode. The power of the projector cannot be turned on
		during the cooling process (180 seconds).


Latest Error	—	Displays the latest error number. Refer to ALatest ErrorB for information
		on the error number and details. (A Page 48)

Signal Status		Displays information on the input signals.
DVI	—	DVI			: Displays the input terminal number.
Rate(Hz)	—	Rate(Hz)			: Displays the vertical frequency.
Pixel H	—	Pixel H			: Displays the horizontal resolution.
Pixel V	—	Pixel V			: Displays the vertical resolution.
Link	—	Link			: Displays the link status of the DVI terminal.

Temperature		Displays the interior temperature of the projector.
Temp. 1	—	Temp. 1			: External Temperature
Temp. 2	—	Temp. 2			: Internal Temperature

Projector Usage		Displays the time interval during which the lamp is in use.
Reset	—	CAUTION:
Reset	—	CAUTION:

●Do not click on AResetB unless the lamp is replaced.

31

Image 31

Barco LX-5 Setting Value Description Power, Latest Error, Signal Status, RateHz, Pixel H, Link, Temperature, Reset

Contents

Lens is optional For Customer use About the installation place Safety PrecautionsMachine Noise Information Germany only Do not allow any unqualified person to install the unit Neutral Safety Precautions Cont’dPower cord Do not cut off the main plug from this equipment EMC Supplement Contents High flexible installation FeaturesUser-friendly interface and high operability Accessories Sold Separately Accessories Viewing Conditions Brightness of Room Precautions During UseMaintenance Procedures Burning-in of D-ILA Device Front/Right Side Names and Functions of Parts Rear Optional projection lens InstallationMinimum Space Required Projector Installation Angle Installing the Projector and Screen LXD 11 Short focal length lens Installing the Projector and Screen Cont’d When shift amount in the left/right direction is 0 % When shift amount in the left direction is -50 % Projecting images by arranging projectors side by side When light passes through the glass of projection booth Approx .03 m Installing the Projector Screen Cont’dScreen Size and Projection Distance LXD 1.5 1.9 Zoom lens LXD 11 Short focal length lens Connection During Single-Screen Mode Display Connecting Video Signals of the Computer Possible Input Signals and Projected Image Connection During Single-Screen Mode Display Connection During Two-Screen/Four Screen Mode Display Connecting Video Signals Computer Cont’d Connection Example During Four-Screen Mode Connection Example During Two-Screen Mode When assigning IP address from the Dhcp server Connection Using a LAN CableSpecifications of PC for Controlling this Projector When assigning a static IP address Is not attached Turning On the Main Power Assigning a static IP address IP Address Settings IP address setting at the computer Default Gateway Deselect the check Select AEnableB Assigning a static IP address Cont’d Cont’d Assigning IP Address from the Dhcp Server Using the Mail Delivery FeatureAfter connecting, turn on the main power Set the Adhcp ClientB setting of this projector to Adhcpb Projecting Image Useful Features During Projection Main Menu Setting Menu Cont’d Temperature Setting Value Description PowerLatest Error Signal Status Image Menu Setting Value Description Input Level Setting MenuDisplay Mode Convergence Menu Setting Value Description RedImage Green color value is fixed Shift This menu is used for adjusting the projection lensLens Menu Focus Option Menu Network Menu Mail Menu Error message sent from this projector Smtp Server Setting Value Description Mail SettingMail Address Command Format Communication SpecificationsRS-232C Interface Parameters used for the data format External control command tableON/OFF Cleaning and Replacing the Filter Maintenance Routine Servicing Replacement of Light Source Lamp Troubleshooting Image is Mode displayImmediately After power is Turned on Screen does Immediately When Projection has Ended Out of Range What to do when these messages are displayedMessage Cause Details Lamp Time Over Check Measure Indicators Measures when the warning mode appears Indicator Description Latest Error Specifications Pin Assignment Specifications Cont’dRS-232C Terminal Pin No Signal Operation Signal Direction DVI-D Terminal Pin No Signal Front Rear Dimensional Outline Drawing Top Side Projector