BBQ Pro 137.23672310 Regulator, Burner And Gas Valve Connection & Operation, Assembly, Page, Step

ASSEMBLY

‡BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY.

‡ASSEMBLE UNIT ON A CLEAN, FLAT SURFACE.

‡TOOLS NEEDED: ADJUSTABLE WRENCH, PHILLIPS HEAD SCREWDRIVER

Carefully position grill as shown.

! !

PERFORM "SOAPY WATER TEST" BEFORE EACH USE. SEE "SOAPY WATER TEST" SECTION IN

MANUAL. EXTINGUISH ALL OPEN FLAMES BEFORE CONNECTING REGULATOR TO GASCYLINDER. TURN GAS OFF AFTER EACH USE.

REGULATOR, BURNER AND GAS VALVE CONNECTION & OPERATION

Do not tighten screws all the way. Leg frames may need to be adjusted during assembly.

STEP 1

Attach rear legs (4), right front leg (25) and left front leg (26) to bottom of smoker body (1) using M6*12(A).

Do not fully tighten screws

STEP2

Attach control panel (5) to right front leg (25) as shown usingM6*12(A).

Repeat on opposite side attaching control panel (5) to left front leg (26).

ƔInspect hose before each use. If there are signs of wear, cuts, or leaks, replace unit. DO NOT USE.

ƔInspect burner before each use. Check burner and burner ventura tube for insects and insect nests. A

Ɣclogged tube can lead to a fi re beneath appliance.

1.Connect hose regulator to LP Gas Cylinder Make sure gas cylinder valve is closed. Turn knob clockwise until it stops.

2.Make sure control knob on smoker is in the “OFF” position.

3.Remove protective cap from gas cylinder and coupling nut if applicable.

4.Center and insert regulator nipple into valve outlet on gas cylinder as shown in fi gure on the left. Turn regulator coupling nut clockwise until it stops. DO NOT OVER TIGHTEN.

ƔPerform Soapy Water Test.

ƔTo use turn gas cylinder ON, turn regulator control valve ON, turn burner control knob clockwise and push ignitor button to light.

ƔIf ignition does not take place within five seconds, turn gas control valve to off position and wait fi ve minutes and repeat lighting procedures. If ignition still

does not occur, see match light directions below.

ƔAfter use turn burner control knob OFF, turn regulator control valve OFF, then turn gas cylinder OFF.

ƔBurner control knob adjusts burner flame. Turn control knob clockwise SLOWLY to increase fl ame. Turn control knob counter-clockwise to decrease flame and shut flame off.

ƔVisually check burner fl ame. A CORRECT FLAME should be blue with a small amount of yellow at the tip. An INCORRECT FLAME is excessively yellow and irregular. If an incorrect flame occurs, turn burner control knob to “OFF

position,

turn off regulator and propane tank. Allow unit to cool and then clean burner.

Let burner completely dry before re-lighting.

ƔThe hose hook must be fasten at the right front leg at anytime and check before ignition. (Please see

ASSEMBLY INSTRUCTION STEP 14)

STEP 3

Position burner box (6) over center hole in bottom of smoker body, carefully aligning venturi over valve orifice as shown. Attach burner box to smoker bod y using M6*12 (A).

Firmly attach ignition wire to piezo ignitor on control panel as shown in

Figure B.

MATCH LIGHT INSTRUCTION

1.	Read all instructions and warnings before lighting.	6. After each use, fi rst
2.	Check gas control valve and gas cylinder valve to be	turn gas control valve off,
certain it is in OFF position before connecting to gas		then gas cylinder valve
cylinder. Perform soapy water test before each use.		off. Always allow unit to
		cool completely before
3.	Open door during lighting.
		touching, moving or
4.	Turn gas control valve on, turn gas cylinder valve on.
		storing.
5.	Place a long, lit fi replace match stick close enough to

burner to ignite.

Page 9 customer service 1-888-577-9820 customer service 1-888-577-9820 Page 6