Presets | Behringer V-AMP PRO, V-AMPIRE, V-AMP 2 manual

V-AMPIRE/V-AMP PRO/V-AMP 2

with effects,

amp and speaker simulation

Studio 1 (S1)

with effects, amp and speaker simulation

Studio 2 (S2)

Amp and speaker simulation, dry

Amp andspeaker simulation

Amp andspeaker simulation, dry

Amp andspeaker simulation

effects

Amp simulation, dry effects

Amp simulation effects

Studio 3 (S3)

with analog ULTRA-G speaker simulation

: Speaker and amp simulation,

Live 1 (L1)

3-band EQ + effects

3-band EQ+ effects

speaker simulation but

speaker simulation

Live 2 (L2)

with 3-band EQ,amp simulation and effects

but with 3-band EQ, amp simulations + effects

with analog ULTRA-G speaker simulation

					Amp simulation with	Amp-, speaker simulation
		Live 3 (L3)			3-band EQ and effects but	and effects but
					speaker simulations	3-band EQ

				Tab. 3.1: Configurations
				4. PRESETS	4.2 Editing presets
				4. PRESETS	4.2 Editing presets
	Your device features 125 overwritable presets divided into 25				Editing presets is fast and simple. One option is to call up a
					preset you like and then start editing it. Select an amp model by
banks. In other words, there are five presets available per bank.
					means of the AMPS encoder. The LED on the preset button
Each preset consists of a maximum of five “ingredients”:					means of the AMPS encoder. The LED on the preset button
Each preset consists of a maximum of five “ingredients”:					flashes (e.g. D) and signals that you have made a change to the

s amp simulation (including GAIN, EQ and VOLUME settings)					preset.
s		cabinet simulation			Now change the settings of the VOLUME, BASS, MID, TREBLE
s pre-amp effect, such as noise gate, compressor, auto wah					and GAIN controls as you like. If you select an effect, you can
s pre-amp effect, such as noise gate, compressor, auto wah					adjust its ratio in the overall sound using the EFFECTS control.
		and wah-wah
		and wah-wah			You then switch to EDIT mode by pressing the arrow keys
					You then switch to EDIT mode by pressing the arrow keys
s post-amp multi-effect, such as delay, modulation effect, or					simultaneously. If you use buttons B - E to activate the DRIVE,
		a combination of both			CABINETS, REVERB and NOISE GATE functions respectively
s		reverb effect			and then edit using the arrow keys, the value of the respective
s		reverb effect			parameter is shown in the display. To quit EDIT mode, briefly

	The enclosed sheet shows an overview of all the presets.				press the TUNER button.
	The enclosed sheet shows an overview of all the presets.
					If you hold the TAP button down while using the TREBLE control,
				4.1 Calling up presets	you can raise or lower an additional high-frequency filter
				4.1 Calling up presets	(PRESENCE). This simulates the frequency-sensitive coupling of

	When the unit is switched on, it automatically loads the last				tube amps.
used preset. In the following example, the last preset selected					+ Apart from compressor and auto wah, all the multi-
was preset D in bank 25:					+ Apart from compressor and auto wah, all the multi-
					effects have a speed-based parameter. Say you
					want to set the effect you’ve selected to the tempo
					want to set the effect you’ve selected to the tempo
					of your playback: just tap the TAP button twice in
					time to the music and the effect tempo will match
					the tempo of your piece.
					4.3 Storing presets
					To store your edited preset, hold down the preset button
					required for approx. 2 seconds for the preset to be overwritten
					(the corresponding LED lights up throughout).
					(the corresponding LED lights up throughout).
					+ You do not necessarily have to store your edited



					preset in place of the original preset selected. If
					you choose a different storage position, select the
					preset bank you want using the arrow keys (BANK
			Fig. 4.1: Calling up presets on the V-AMP 2		preset bank you want using the arrow keys (BANK
			Fig. 4.1: Calling up presets on the V-AMP 2		UP and BANK DOWN). You can store your changes by
				(similar to V-AMPIRE and V-AMP PRO)	UP and BANK DOWN). You can store your changes by
				(similar to V-AMPIRE and V-AMP PRO)	holding down the preset button for approx. two
					holding down the preset button for approx. two
	In this case, by pressing button A, B, C or E you can immediately				seconds. For example,	you can edit a preset
					originally stored in bank 5, position D, and then store
call up another preset of the same bank. The two arrow keys					originally stored in bank 5, position D, and then store
call up another preset of the same bank. The two arrow keys					it in bank 6, position A.
(BANK UP and BANK DOWN) enable you to switch banks. The					it in bank 6, position A.
(BANK UP and BANK DOWN) enable you to switch banks. The
display always shows which bank has been selected. When
you switch banks, the preset has to be called up by pressing
one of the buttons A - E. One LED lights up to show you which
preset in the respective bank has been activated.

10	4. PRESETS

Behringer V-AMP PRO, V-AMPIRE, V-AMP 2 manual Presets

Models: V-AMP PRO V-AMP 2 V-AMPIRE

V-AMPIRE/V-AMP PRO/V-AMP 2

4. PRESETS

4.2 Editing presets

4.1 Calling up presets

4.3 Storing presets

Fig. 4.1: Calling up presets on the V-AMP 2

UP and BANK DOWN). You can store your changes by

(similar to V-AMPIRE and V-AMP PRO)

holding down the preset button for approx. two