Manuals / Belshaw Brothers / Kitchen Appliance / Fryer

Belshaw Brothers 718LCG Unpacking the Fryer, Initial Cleaning, Assembling the Fryer, are dry

Models: 718LCG 724CG and 734CG

1 42

Download 42 pages 26.76 Kb

Page 8

Unpacking the Fryer

The workstation should allow at least 2”/5 cm clearance between the machine and all construction, whether combustible or noncombustible. In addition, it should allow access to the rear of the fryer for cleaning and servicing.

Unpacking the Fryer

1.Use a fork lift to transport the shipping crate to the work station.

2.Break down the shipping crate.

3.Remove all the packing materials from the fryer. These include foam, tape, brown paper, plastic, and white protective coating.

4.Position the fryer to allow sufficient space on either end of the machine for any equipment you plan to use with it.

Initial Cleaning

Clean your fryer before using it. Wipe the inside of the kettle with a soft, damp cloth. Dry the kettle thoroughly.

WARNING

To avoid electrocuting yourself or

damaging the machine, never allow water, steam, cleaning solution, or other liquid to enter the electrical box.

WARNING

Never let water and hot shortening come in contact with each other. Moisture causes hot shortening to spatter, which may cause serious injury. Prior to use, make sure the kettle and any other parts you have washed

are dry.

Assembling the Fryer

1.Install the flue stack as follows:

a.Slide the flange on the bottom of the flue stack underneath the retaining strip on the flue base. The mounting holes must line up. (See Figure 1-1.)

b.Fasten the flue stack to the flue base using the two pan-head sheet metal screws provided.

flue stack

retaining strip

flue base

pan-head sheet metal screw

Figure 1-1. Installing the Flue Stack.

2.Attach the heat shield to the splash shield as follows:

a.Slide the flanges on the sides of the heat shield under the bent edges of the splash shield. The mounting holes must line up.

b.Fasten the heat shield to the splash shield using the 10-24 x 3/8” hex-head screws, lockwashers, and nuts provided. The screws go through the front of the splash shield; the lockwashers and nuts go on the back of the heat shield.

Belshaw Bros., Inc. • 1750 22nd Ave. S. • Seattle, WA 98144 • Phone 206-322-5474 • Fax 206-322-5425

2

MN-1141EN

718LCG, 724CG, and 734CG Gas Fryers

Image 8

Belshaw Brothers 718LCG Unpacking the Fryer, Initial Cleaning, Assembling the Fryer, To avoid electrocuting yourself or

Contents

Models 718LCG 724CG and 734CG Operator’s ManualGas Fryer Seattle, WA 98144-4590 USA Phone 206 322-5474 Fax 206 Toll Free EQUIPMENT RECORD0606 MN-1141EN Belshaw Bros., Inc 1750 22nd Avenue South Contents InstallationCleaning MaintenanceParts Lists Limited WarrantyCalculating Correct Water Temperature Ratios of Plunger Sizes to Donut WeightsPreface Page 1Installation FOR YOUR SAFETYConforming to Codes Selecting a WorkstationInitial Cleaning Unpacking the FryerAssembling the Fryer To avoid electrocuting yourself orTo avoid damaging the fryer, do not Installing the Fryer0.5 psig/3.45 kPa when the fryer is connected to the that system Moving the Fryer Frying Donuts Taking Safety PrecautionsOperation2 Failure to wait at least one minute for the gas to dissipate could result in a fire or an explosion when the pilot is lighted again To avoid damaging the machine, do not operate the conveyor until all the shortening has melted3Cleaning Removing the ShorteningWashing Rinsing Maintenance4 Use Rev. 3 to correct existing open Kettle Fryer settingsSB-0308 rev AFFECTSMenu Overview Figure 2 - Menu Flow ChartMN-1141EN 718LCG, 724CG, and 734CG Gas FryersOpen Kettle Fryer Parameter Settings Default Settings718LCG, 724CG, and 734CG Gas Fryers MN-1141ENsetup 0ºF 410ºF 0ºF MN-1141EN718LCG, 724CG, and 734CG Gas Fryers Table 1 - Parameter Descriptions Set to 375ºF set to “uSEr” afterTable 2 - Parameter Descriptions Set to “nonE” 718LCG, 724CG, and 734CG Gas FryersMN-1141EN Table 3 - Parameter Descriptions Set to MN-1141EN718LCG, 724CG, and 734CG Gas Fryers 5Troubleshooting Page Pilot Module CheckoutStep 1 Perform Visual Inspection Step 2 Review the Normal Operating SequenceMain Burner Operation Step 3 Reset the ModuleStep 4 Check Safety Shutoff Operation Figure A-1. Normal Operating Sequence 718LCG, 724CG, and 734CG Gas FryersMN-1141EN START TRIAL FOR IGNITION MAIN BURNER OPERATIONTroubleshooting the Ignition System Troubleshooting-GeneralStep 5 Check Normal Operation Step 1 Check Ignition CableStep 3 Check Spark Ignition Circuit Step 4 Check Pilot and Main Burner LightoffArc Length What To DoAppearance CauseMN-1141EN 718LCG, 724CG, and 734CG Gas FryersB Donut-Making Helps Tips on Making Quality Cake DonutsCalculating Correct Water Temperature Ratios of Plunger Sizes to Donut WeightsTemperature Conversion Donut Weight permeant as guides. Because Belshaw Parts ListsThe parts lists and assembly drawings are 718LCG PARTS LIST MN-1141EN718LCG, 724CG, and 734CG Gas Fryers NUMBER718LCG PARTS LIST CONT’D 718LCG, 724CG, and 734CG Gas FryersMN-1141EN NUMBER724CG PARTS LIST GAS VALVE ASSEMBLYMN-1141EN 718LCG, 724CG, and 734CG Gas FryersMN-1141EN 734CG PARTS LIST718LCG, 724CG, and 734CG Gas Fryers 0080A5 MN-1141EN718LCG, 724CG, and 734CG Gas Fryers MN-1141EN 734FG PARTS LIST718LCG, 724CG, and 734CG Gas Fryers Page US/Canada/Mexico Limited Warranty and Return Policy Procedure for Return ExclusionsReturn goods must be Please note the following