Lock, Background, Color Splash, Screen, High, Altitude | BenQ MS504

4. SYSTEM SETUP: Basic menu 5. SYSTEM SETUP: Advanced menu

Function	Description
Panel Key	Disables or enables all panel key functions except		POWER on the


Lock	projector and keys on the remote control. See "Locking control keys"
	on page 31 for details.
Background	Sets the background color for the projector.
Color

Splash	Allows you to select which logo screen will display during projector
Screen	start-up.

	High	A mode for operation in high altitude areas. See "Operating in a high
	Altitude
	Altitude	altitude environment" on page 31 for details.
	Mode	altitude environment" on page 31 for details.
	Mode

	Audio	See "Adjusting the sound" on page 32 for details.
	Settings	See "Adjusting the sound" on page 32 for details.
	Settings

		Lamp Mode
		See "Setting the Lamp Mode" on page 46 for details.
	Lamp	Reset Lamp Timer
	Settings	See "Resetting the lamp timer" on page 48 for details.
	Settings	Equivalent Lamp
		Equivalent Lamp
		See "Getting to know the lamp hour" on page 46 for details on how the
		total lamp hour is calculated.
	Security	See "Utilizing the password function" on page 21 for details.
	Settings
	Settings

		Selects a baud rate that is identical with your computer’s so that you
	Baud Rate	can connect the projector using a suitable RS-232 cable and update or
	Baud Rate	download the projector’s firmware. This function is intended for

		qualified service personnel.

	Test Pattern	See "Using the test pattern" on page 32 for details.

42 Operation

Image 42

BenQ MS504, MX505 Lock, Background, Color Splash, Screen, High, Altitude, Audio, Lamp, Security, Baud Rate, Test Pattern

Contents

MS504/MX505 Digital Projector Table of contents Important safety instructions Safety Instructions Safety Instructions 3000 m Feet Ceiling mounting the projector Projector features Introduction Shipping contents Projector exterior view Front/upper side Rear/lower side Controls and functions Remote control Remote control effective range Replacing the remote control batteries Front Table Positioning your projectorChoosing a location Front Ceiling Projection dimensions Obtaining a preferred projected image size Connection Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Component Video Better Good Normal Operation Starting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystone Using the menus Below is the overview of the OSD menu Setting a password Using a security cable lockUtilizing the password function If you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Switching input signal Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature Setting a preferred color temperature 3D Color Management Setting the presentation timer Resetting current or all picture modesSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-Right Locking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environment Adjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring Tone Using the teaching templates To select Blackboard or Whiteboard Direct power off Shutting down the projector Menu system Teaching Coordinate Chart Template WhiteboardMenu operation Main menu Sub-menu Options Menu Display Sec/10 sec/20 sec/30 sec BasicCeiling/Front Ceiling Time Always Advanced Description of each menu Teaching Template Description Apply 3D SettingsSave 3D Settings 3D Sync Invert Color Temperature Function Description Picture ModeTemperature Fine Tuning 3D Color Installation System Setup Basic menu Function Description PresentationTimer Settings Color Splash LockBackground Screen Closed System Setup Advanced menu Function DescriptionReset All Caption Current SystemStatus Maintenance Care of the projector Lamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Status Message Resetting the lamp timer Replacing the lamp Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Copyright Warranty and Copyright informationLimited warranty Disclaimer