Operation, Starting up the projector | BenQ MX505, MS504 specification

Operation

Starting up the projector

1.Plug the power cord into the projector and into a

power outlet. Turn on the power outlet switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied.

Please use the original accessories (e.g. power cord) only with the device to avoid possible dangers such as electric shock and fire.

2.Press POWER to start the projector. As soon as the lamp lights up, a "Power On Ring Tone" will be heard. The POWER indicator light flashes green and stays green when the projector is on.

The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected.

(If necessary) Rotate the focus ring to adjust the image clearness.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 32 for details.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.

3.If the projector is activated for the first time, select your OSD language following the on-screen instructions.

4.If you are prompted for a password, press the arrow keys to enter a six-digit password. See "Utilizing the password function" on page 21 for details.

5.Switch all of the connected equipment on.

6.The projector will start to search for input signals. The current input signal being scanned appears in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message “No Signal” will continue displaying until an input signal is found.

You can also press SOURCE on the projector or remote control to select your desired input signal. See "Switching input signal" on page 23 for details.

•If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message “Out of Range” displayed on the background screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 53 for details.

•If no signal is detected for 3 minutes, the projector automatically enters ECO BLANK mode.

Operation 17

Image 17

BenQ MX505, MS504 user manual Operation, Starting up the projector

Contents

MS504/MX505 Digital Projector Table of contents Safety Instructions Important safety instructions Safety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector features Shipping contents Front/upper side Rear/lower side Projector exterior view Controls and functions Remote control Replacing the remote control batteries Remote control effective range Choosing a location Positioning your projectorFront Table Front Ceiling Obtaining a preferred projected image size Projection dimensions Connection Connection Connecting audio Connecting video source devicesTerminal name Terminal appearance Component Video Better Good Normal Starting up the projector Operation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystone Below is the overview of the OSD menu Using the menus Utilizing the password function Using a security cable lockSetting a password If you forget the password Disabling the password function Entering the password recall procedureChanging the password Switching input signal Selecting the aspect ratio Magnifying and searching for details About the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Selecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Setting a preferred color temperature Selection Description Setting the presentation timerResetting current or all picture modes Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-Right Hiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environment Using the test pattern Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring Tone To select Blackboard or Whiteboard Using the teaching templates Shutting down the projector Direct power off Menu operation Teaching Coordinate Chart Template WhiteboardMenu system Main menu Sub-menu Options Ceiling/Front Ceiling BasicMenu Display Sec/10 sec/20 sec/30 sec Time Always Advanced Description of each menu Save 3D Settings Apply 3D SettingsTeaching Template Description 3D Sync Invert Temperature Function Description Picture ModeColor Temperature Fine Tuning 3D Color Timer System Setup Basic menu Function Description PresentationInstallation Settings Background LockColor Splash Screen Reset All System Setup Advanced menu Function DescriptionClosed Caption Status CurrentSystem Care of the projector Maintenance Extending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lamp Replacing the lamp Resetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal events Troubleshooting Projector specifications Specifications Ceiling mount installation Dimensions Supported timing for PC input Timing chart Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright Disclaimer