Manuals / BenQ / Computer Equipment / Projector

BenQ ms616st, mx618st Main menu, Sub-menu, Options, System, Setup, Advanced, Informa, Tion

Models: ms616st mx618st

1 58

Download 58 pages 15.75 Kb

Page 39

	Main menu	Sub-menu		Options

		Quick Cooling		On/Off
		High Altitude Mode		On/Off
			Mute	On/Off
		Audio Settings	Volume
		Audio Settings	Power On/Off	On/Off
			Power On/Off
			Ring Tone
			Ring Tone
			Lamp Mode	Normal/Economic/SmartEco
		Lamp Settings	Reset Lamp Timer
			Equivalent Lamp Hour
		Security	Change Password
		Security	Change Security
	5.	Settings	Change Security	Power On Lock
	5.		Settings
	SYSTEM	Baud Rate		2400/4800/9600/14400/19200/
	SYSTEM	Baud Rate		38400/57600/115200
	SETUP:			38400/57600/115200
	SETUP:	Test Pattern		On/Off
	Advanced	Test Pattern		On/Off
	Advanced		Closed Caption	On/Off
			Closed Caption
		Closed Caption	Enable
		Closed Caption	Enable
			Caption Version	CC1/CC2/CC3/CC4
		Standby	Network	On/Off
		Settings	Monitor Out	On/Off
				Status
			Wireless LAN	SSID
		Network	Wireless LAN	IP Address
		Network		IP Address
		Settings		Connection Mode
			Projection Log In	On/Off
			Code
		Reset All Settings
				•	Source
	6.			•	Picture Mode
	INFORMA	Current System Status		•	Resolution
	INFORMA	Current System Status		•	Color System
	TION			•	Color System
	TION			•	Equivalent Lamp Hour
				•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Operation 39

Image 39

BenQ ms616st Main menu, Sub-menu, Options, System, Setup, Advanced, Informa, Tion, Reset Lamp Timer, Change Password

Contents

User Manual MS616ST/MX618ST Digital ProjectorMaintenance Table of contentsImportant safety Warranty and CopyrightSafety Instructions Important safety instructionsSafety Instructions Continued 3000 m 10000 feet 0 m 0 feet Ceiling mounting the projector Introduction Projector featuresShipping contents Standard accessoriesOptional accessories Projector exterior view Front/upper sideRear/lower side Focus ring Controls and functionsProjector LAMP indicator light10. Page Up/Page Down Remote controlReplacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Projection dimensionsConnection Connecting audio Connecting video source devicesStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageto correct keystoning at the top of the Correcting keystoneUsing the menus If you forget the password Using a security cable lockUtilizing the password function Setting a password2. Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears Entering the password recall procedureChanging the password Disabling the password functionChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailshorizontal or vertical width. This is suitable About the aspect ratioAuto Scales an image proportionally to fit 169 Scales an image so that it isOptimizing the image Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeAdjusting Color Fine-tuning the image quality in user modesAdjusting Brightness Adjusting Contrastto highlight Saturation and adjust 3D Color ManagementTo cancel the timer, perform the following steps Setting the presentation timerFreezing the image Remote paging operationsBe sure the SYSTEM SETUP Basic Auto Blank menu is On Hiding the imageLocking control keys Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the soundUsing the test pattern Teaching Using the teaching templatesLetter Formation Worksheet Coordinate Chart to select Blackboard or WhiteboardSupported image formats When viewing thumbnailsSetting page Presenting from a USB ReaderShutting down the projector Direct power offMenu system Menu operationOptions SETUPMain menu Sub-menuMain menu SETUPReset Lamp Timer Change PasswordDescription of each menu See Adjusting Brilliant Color on page 27 for details See Using the teaching templates on page 34 for detailspicture mode on page 26 for details See Adjusting Contrast on page 27 for detailsSets the length of time the OSD will remain active after your last key See Utilizing the password function on page 21 for details See Adjusting the sound on page 32 for detailsSee Setting Lamp Mode as Economic or SmartEco on page 46 for details See Resetting the lamp timer on page 50 for detailsmenu Care of the projector MaintenanceCleaning the lens Cleaning the projector caseLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Install a new lamp for optimal performance. If thewhenever you notice that the brightness level has cover on the side of the projector until the lamp cover loosens Replacing the lamp48 Maintenance 2. Loosen the screw that secures the lamp6. Use the handle to slowly pull the lamp out of the projector Resetting the lamp timer Status & Description IndicatorsPower events LightTroubleshooting Please see Entering the password recallprocedure on page 22 for details Projector specifications Specifications312 mm W x 104 mm H x 244 mm D DimensionsCeiling mount installation 54 SpecificationsPixel Timing chartSupported timing for PC input UXGASupported timing for HDMI HDCP input 56 SpecificationsPixel Timing Supported timing for Component-YPbPr inputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright