Manuals / BenQ / Computer Equipment / Projector

BenQ ms616st, mx618st Indicators, Light, Status & Description, Power events, Lamp events

Models: ms616st mx618st

1 58

Download 58 pages 15.75 Kb

Page 51

Indicators

Indicators

Light

Status & Description

Power events

	Orange	Off	Off	Stand-by mode.
	Green	Off	Off	Powering up.
	Flashing	Off	Off	Powering up.
	Flashing
	Green	Off	Off	Normal operation.
	Orange	Off	Off	Normal power-down cooling
	Flashing	Off	Off	Normal power-down cooling
	Flashing
			Lamp events

	Off	Off	Red	Lamp error in normal operation
	Orange	Off	Red	Lamp is not lit up
	Flashing	Off	Red	Lamp is not lit up
	Flashing
			Thermal events
	Off	Red	Off	Fan 1 error (the actual fan speed is +25% outside
	Off	Red	Off	the desired speed)
				the desired speed)
	Off	Red	Red	Fan 2 error (the actual fan speed is +25% outside
	Off	Red	Red	the desired speed)
				the desired speed)
	Off	Red	Green	Fan 3 error (the actual fan speed is +25% outside
	Off	Red	Green	the desired speed)
				the desired speed)
	Off	Red	Orange	Fan 4 error (the actual fan speed is +25% outside
	Off	Red	Orange	the desired speed)
				the desired speed)
	Orange	Red	Red	Temperature 1 error (over limited temperature)
	Red	Red	Red	Thermal Sensor 1 open error
	Green	Red	Red	Thermal Sensor 1 short error
	Off	Green	Red	Fan IC #1 I2C Connection error
	Orange	Red	Green	Temperature 2 error (over limited temperature)
	Red	Red	Green	Thermal Sensor 2 open error
	Green	Red	Green	Thermal Sensor 2 short error
	Off	Green	Orange	Fan IC #2 I2C Connection error
	Off	Red	Off	Fans do not rotate in the process of powering up

Maintenance 51

Image 51

BenQ ms616st, mx618st user manual Indicators, Light, Status & Description, Power events, Lamp events

Contents

User Manual MS616ST/MX618ST Digital ProjectorMaintenance Table of contentsImportant safety Warranty and CopyrightSafety Instructions Important safety instructionsSafety Instructions Continued 3000 m 10000 feet 0 m 0 feet Ceiling mounting the projector Introduction Projector featuresShipping contents Standard accessoriesOptional accessories Projector exterior view Front/upper sideRear/lower side Focus ring Controls and functionsProjector LAMP indicator light10. Page Up/Page Down Remote controlReplacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Projection dimensionsConnection Connecting audio Connecting video source devicesStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageto correct keystoning at the top of the Correcting keystoneUsing the menus If you forget the password Using a security cable lockUtilizing the password function Setting a password2. Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears Entering the password recall procedureChanging the password Disabling the password functionChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailshorizontal or vertical width. This is suitable About the aspect ratioAuto Scales an image proportionally to fit 169 Scales an image so that it isSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Optimizing the imageAdjusting Color Fine-tuning the image quality in user modesAdjusting Brightness Adjusting Contrastto highlight Saturation and adjust 3D Color ManagementTo cancel the timer, perform the following steps Setting the presentation timerFreezing the image Remote paging operationsBe sure the SYSTEM SETUP Basic Auto Blank menu is On Hiding the imageLocking control keys Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the soundUsing the test pattern Teaching Using the teaching templatesLetter Formation Worksheet Coordinate Chart to select Blackboard or WhiteboardSupported image formats When viewing thumbnailsSetting page Presenting from a USB ReaderShutting down the projector Direct power offMenu system Menu operationOptions SETUPMain menu Sub-menuMain menu SETUPReset Lamp Timer Change PasswordDescription of each menu Adjusts the degree of difference between dark and light in the image See Using the teaching templates on page 34 for detailsSee Adjusting Contrast on page 27 for details See Adjusting Brilliant Color on page 27 for detailsSets the length of time the OSD will remain active after your last key See Utilizing the password function on page 21 for details See Adjusting the sound on page 32 for detailsSee Setting Lamp Mode as Economic or SmartEco on page 46 for details See Resetting the lamp timer on page 50 for detailsmenu Care of the projector MaintenanceCleaning the lens Cleaning the projector caseLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Install a new lamp for optimal performance. If thewhenever you notice that the brightness level has cover on the side of the projector until the lamp cover loosens Replacing the lamp48 Maintenance 2. Loosen the screw that secures the lamp6. Use the handle to slowly pull the lamp out of the projector Resetting the lamp timer Status & Description IndicatorsPower events LightTroubleshooting Please see Entering the password recallprocedure on page 22 for details Projector specifications Specifications312 mm W x 104 mm H x 244 mm D DimensionsCeiling mount installation 54 SpecificationsPixel Timing chartSupported timing for PC input UXGASupported timing for HDMI HDCP input 56 SpecificationsPixel Timing Supported timing for Component-YPbPr inputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright